Data flagging with plotms

Casaplotms is (currently) a standalone tool to inspect and edit measurement sets. This tutorial demonstrates how to use casaplotms to edit a multisource continuum data set: VLA program AU079, which consists of L-band (20 cm) continuum observations of galaxies and calibrator sources. It is the same data set used in the Imaging Flanking Fields tutorial, as well as the Data flagging with viewer tutorial.

Loading the Measurement Set into Casaplotms

As described in the Imaging Flanking Fields tutorial, the data may be loaded into CASA using the importvla command. The following commands import the data into the measurement set au079.ms and exit CASA to the command line.

# import the glob command for filename searching with wildcards
from glob import glob

# Define the list of files for reading. Use glob to perform wildcard matching with VLA archive filenames.
fileList = glob('AU079_*.xp?')

importvla(archivefiles=fileList,vis='au079.ms')
exit()

Now start up casaplotms from the command line.

# in bash
casaplotms

This command brings up the PlotMS window, shown with annotations at right. The window comprises three panels: the control panel (outlined in blue), the graphics panel (green), and the tools panel (red). The control panel controls the selection of data for display and the graphing parameters (axis selection, axis limits, and so on). The graphics panel is the display panel for two-dimensional (x, y) projections of the data. The tools panel provides commands to interact with the graphics panel. The control panel further breaks down into a series of tabs, annotated as Top Tabs and Side Tabs, which contain related plotting and editing control parameters. This tutorial employs only the Plots tab among the Top Tabs and the following Side Tabs. MS, which controls the selection of the measurement set proper and the selection of data within the measurement set. Axes, which controls the selection of data and plotting parameters for the (x, y) graph. Plot, which affects the style of plotting symbols, whether or not flagged data points are shown, and axis labels. Flagging, which controls how flagging commands are extended (as of 1 Dec 2009, these flagging extensions are very limited but will likely improve as casaplotms continues development). In this tutorial, interactive commands in the PlotMS window will be summarized as (Tab)Command,, where (Tab) represents the Side Tab where the command is found, and Command is the appropriate GUI interaction (button press, text field, checkbox, etc.). Use the (MS)Browse button, or enter the full pathname, to navigate to and select the measurement set (here, au079.ms). Click to enlarge

Identifying Bad Data by Discrepant Amplitudes

Have a first look at the data by hitting the (MS)Plot button. By default, the axes will be visibility amplitude vs. time. The x-axis labeling is a little garbled in this development version of the software, but straightaway there appear some wildly discrepant data. For a typical decimeter-wave continuum data set, sources and calibrators are expected to show visibility amplitudes of a few Jy or less; visibilities with amplitudes in the 100s of Jy range are likely bogus. Here's how to flag them. Click to enlarge

There's a simple pattern to flagging in casaplotms. Highlight the data to be flagged using the Mark Regions tool. Flag the data in the highlighted region using the Flag tool. The figure at right shows a highlighted region selected using the Mark Regions tool. After flagging, those data will be removed from the display unless (Plot)Flagged Points Symbol is set. Click to enlarge

The figure at right shows a close-up of the data that remain. The y-axis scale was reduced to the range (0, 100 Jy) by using the (Axes)Range controls. Notice that you can set more than one region with the Mark Regions tool before flagging. Click to enlarge

Tip: The automatic scaling of the data axes are cached and so are unaffected by flagging. To rescale (semi-) automatically, change the 
(Axes)X Axis to some other arbitrary projection (say, Scan), (Axes)Plot, and then reset (Axes)X Axis to its original state
(say, Time).

After zapping those obviously high visibilities, things become a little more challenging. Click to enlarge

Antenna-Based Flagging

--Jack Gallimore 14:38, 1 December 2009 (UTC)