EVLA Continuum Tutorial 3C391 CASA 4.2
This is the first part of the EVLA 3C391 data reduction tutorial. The second is 3C391 Tutorial Part 2: Image Analysis, Polarization, Self-calibration which follows on from this one.
This CASA Guide is for Version 4.2.0 of CASA.
Overview
This article describes the calibration and imaging of a multiple-pointing EVLA continuum dataset on the supernova remnant 3C 391. The data were taken in EVLA early science OSRO1 mode, with 128 MHz of bandwidth in each of two widely spaced spectral windows, centered at 4.6 and 7.5 GHz, and were set up for full polarization calibration.
There are a number of possible ways to run CASA, described in more detail in Getting Started in CASA. In brief, there are at least three different ways to run CASA:
- Interactively examining task inputs. In this mode, one types default taskname to load the task, inp to examine the inputs, and go once those inputs have been set to your satisfaction. Allowed inputs are shown in blue, and bad inputs are colored red. The inputs themselves are changed one by one, e.g., selectdata=T. Screenshots of the inputs to various tasks used in the data reduction below are provided, to illustrate which parameters need to be set.
More detailed help can be obtained on any task by typing help taskname. Once a task is run, the set of inputs are stored and can be retrieved via tget taskname; subsequent runs will overwrite the previous tget file.
- Pseudo-interactively via task function calls. In this case, all of the desired inputs to a task are provided at once on the CASA command line. This tutorial is made up of such calls, which were developed by looking at the inputs for each task and deciding what needed to be changed from default values. For task function calls, only parameters that you want to be different from their defaults need to be set.
- Non-interactively via a script. A series of task function calls can be combined together into a script, and run from within CASA via execfile('scriptname.py'). This (and other) CASA Guides have been designed to be extracted into a script using the script extractor. Should one use the script generated by the script extractor for this CASA Guide, be aware that it will require some small amount of interaction related to the plotting, occasionally suggesting that you close the graphics window and hitting return in the terminal to proceed. It is in fact unnecessary to close the graphics windows (it is suggested that you do so purely to keep your desktop uncluttered).
If you are a relative novice (and particularly for this tutorial), it is strongly recommended that you start with the interactive mode, graduating to the pseudo- or non-interactive mode as you gain experience. Work at your own pace, look at the inputs to the tasks to see what other options exist, and read the help files.
Obtaining the Data
For the purposes of this tutorial, we have created a "starting" data set, upon which several initial processing steps have already been conducted. If you are running this Guide outside of a workshop (in which case the data are probably already on your machine), you may obtain it from here: http://casa.nrao.edu/Data/EVLA/3C391/3c391_ctm_mosaic_10s_spw0.ms.tgz (dataset size: 3.1GB)
We are providing this "starting" data set, rather than the "true" initial data set for (at least) two reasons. First, many of these initial processing steps can be rather time consuming (> 1 hr). Second, while necessary, many of these steps are not fundamental to the calibration and imaging process, upon which we want to focus today. For completeness, however, here are the steps that were taken from the initial data set to produce the "starting" data set.
- The initial Science Data Model (SDM) file was converted into a measurement set.
- Basic data flagging was applied, to account for "shadowing" of the antennas. These data are from the D configuration, in which antennas are particularly susceptible to being blocked or "shadowed" by other antennas in the array, depending upon the elevation of the source.
- The data were averaged to 10-second samples, from the initial 1-second correlator sample time. In the D configuration, the fringe rate is relatively slow and time-average smearing is less of a concern.
- The data were acquired with two spectral windows (around 4.6 and 7.5 GHz). Because of disk space concerns on some machines, the focus will be on only one of the two spectral windows.
All of these steps can be done directly from the NRAO Archive's Download page, by selecting "CASA MS" as the download format (it's a good idea to also check the "Create MS or SDM tar file" box), checking the "Apply flags generated during observing" box, and setting "Time Averaging" to 10s.
The Observation
Before starting the calibration process, we want to get some basic information about the data set. To examine the observing conditions during the observing run, and to find out any known problems with the data, download the observer log. Simply fill in the known observing date (in our case 2010-Apr-24) as both the Start and Stop date, and click on the "Show Logs" button. The relevant log is labeled with the project code, TDEM0001, and can be downloaded as a PDF file. From this, we find the following:
Information from observing log: There is no C-band receivers on ea13 Antenna ea06 is out of the array Antenna ea15 has some corrupted data Antennas ea10, ea12, ea22 do not have good baseline positions Gusty winds, mixed clouds, API rms up to 11.5.
Before beginning our data reduction, we must start CASA. If you have not used CASA before, some helpful tips are available on the Getting Started in CASA page.
Once you have CASA up and running in the directory containing the data, then start your data reduction by getting some basic information about the data. The task listobs can be used to get a listing of the individual scans comprising the observation, the frequency setup, source list, and antenna locations.
# In CASA
listobs(vis='3c391_ctm_mosaic_10s_spw0.ms')
One will note that there are nine sources observed. Here the various sources are introduced briefly, with more detail contained in the sections below in which they are used.
- J1331+3030 = 3C 286, which will later serve as a calibrator for the visibility amplitudes, i.e., it is assumed to have a precisely known flux density; the spectral bandpass; and the polarization position angle;
- J1822-0938, which will serve as a calibrator for the visibility phases;
- J0319+4130 = 3C 84, which will serve as a polarization calibrator; and
- 3C391 C1--C7, which are 7 fields centered on and surrounding the supernova remnant.
This observation was set up as a 7-pointing mosaic because the supernova remnant is so large that it essentially fills the primary beam.
##########################################
##### Begin Task: listobs #####
listobs(vis="3c391_ctm_mosaic_10s_spw0.ms",selectdata=True,spw="",field="",
antenna="",uvrange="",timerange="",correlation="",scan="",
intent="",feed="",array="",observation="",verbose=True,
listfile="",listunfl=False,cachesize=50)
================================================================================
MeasurementSet Name: /Science/CASA_Guides/3C391_CASA4.1/3c391_ctm_mosaic_10s_spw0.ms MS Version 2
================================================================================
Observer: Dr. James Miller-Jones Project: T.B.D.
Observation: EVLA
Data records: 845379 Total integration time = 28671.5 seconds
Observed from 24-Apr-2010/08:02:15.0 to 24-Apr-2010/16:00:06.5 (UTC)
ObservationID = 0 ArrayID = 0
Date Timerange (UTC) Scan FldId FieldName nRows SpwIds Average Interval(s) ScanIntent
24-Apr-2010/08:02:10.4 - 08:02:29.5 1 0 J1331+3030 650 [0] [10]
08:02:24.5 - 08:09:29.1 2 0 J1331+3030 13975 [0] [10]
08:09:24.0 - 08:16:28.0 3 0 J1331+3030 13975 [0] [10]
08:19:38.0 - 08:24:26.5 4 1 J1822-0938 7035 [0] [10]
08:24:48.0 - 08:29:46.5 5 2 3C391 C1 7590 [0] [10]
08:29:41.5 - 08:34:46.0 6 3 3C391 C2 7821 [0] [10]
08:34:41.0 - 08:39:45.5 7 4 3C391 C3 7821 [0] [10]
08:39:39.0 - 08:44:45.0 8 5 3C391 C4 7821 [0] [10]
08:44:40.0 - 08:49:44.5 9 6 3C391 C5 7843 [0] [10]
08:49:39.4 - 08:54:44.5 10 7 3C391 C6 7843 [0] [10]
08:54:39.5 - 08:59:43.5 11 8 3C391 C7 7843 [0] [10]
09:00:03.0 - 09:01:31.0 12 1 J1822-0938 2925 [0] [10]
09:01:52.0 - 09:06:50.5 13 2 3C391 C1 7941 [0] [10]
09:06:45.5 - 09:11:50.0 14 3 3C391 C2 9801 [0] [10]
09:11:45.0 - 09:16:49.5 15 4 3C391 C3 10075 [0] [10]
09:16:44.5 - 09:21:49.0 16 5 3C391 C4 10050 [0] [10]
09:21:44.0 - 09:26:48.5 17 6 3C391 C5 10075 [0] [10]
09:26:43.5 - 09:31:48.5 18 7 3C391 C6 10075 [0] [10]
09:31:43.5 - 09:36:47.5 19 8 3C391 C7 10075 [0] [10]
09:37:07.0 - 09:38:35.0 20 1 J1822-0938 2900 [0] [10]
09:38:57.0 - 09:43:55.0 21 2 3C391 C1 9700 [0] [10]
09:43:50.0 - 09:48:54.5 22 3 3C391 C2 10050 [0] [10]
09:48:49.5 - 09:53:54.0 23 4 3C391 C3 10075 [0] [10]
09:53:49.0 - 09:58:53.5 24 5 3C391 C4 10075 [0] [10]
09:58:48.5 - 10:03:53.0 25 6 3C391 C5 10075 [0] [10]
10:03:48.0 - 10:08:52.5 26 7 3C391 C6 10075 [0] [10]
10:08:47.5 - 10:13:47.0 27 8 3C391 C7 9750 [0] [10]
10:14:12.0 - 10:15:39.5 28 1 J1822-0938 2925 [0] [10]
10:16:01.0 - 10:20:58.5 29 2 3C391 C1 9000 [0] [10]
10:20:53.5 - 10:25:58.6 30 3 3C391 C2 10050 [0] [10]
10:25:53.5 - 10:30:58.0 31 4 3C391 C3 10075 [0] [10]
10:30:53.0 - 10:35:57.5 32 5 3C391 C4 10075 [0] [10]
10:35:52.5 - 10:40:57.0 33 6 3C391 C5 10075 [0] [10]
10:40:52.0 - 10:45:56.5 34 7 3C391 C6 10075 [0] [10]
10:45:51.5 - 10:50:51.0 35 8 3C391 C7 9750 [0] [10]
10:51:15.0 - 10:52:42.5 36 1 J1822-0938 2925 [0] [10]
10:55:14.0 - 10:57:42.0 37 0 J1331+3030 3364 [0] [10]
11:00:13.0 - 11:02:41.0 38 1 J1822-0938 3883 [0] [10]
11:03:03.0 - 11:08:01.0 39 2 3C391 C1 9750 [0] [10]
11:07:56.0 - 11:12:50.5 40 3 3C391 C2 9725 [0] [10]
11:12:45.5 - 11:17:40.1 41 4 3C391 C3 9750 [0] [10]
11:17:35.0 - 11:22:29.5 42 5 3C391 C4 9750 [0] [10]
11:22:24.5 - 11:27:19.5 43 6 3C391 C5 9750 [0] [10]
11:27:14.5 - 11:32:09.0 44 7 3C391 C6 9750 [0] [10]
11:32:04.0 - 11:36:53.0 45 8 3C391 C7 9425 [0] [10]
11:37:21.0 - 11:38:47.0 46 1 J1822-0938 2700 [0] [10]
11:39:11.0 - 11:44:07.0 47 2 3C391 C1 9750 [0] [10]
11:44:02.0 - 11:48:56.5 48 3 3C391 C2 9700 [0] [10]
11:48:51.5 - 11:53:41.0 49 4 3C391 C3 8355 [0] [10]
11:53:41.0 - 11:58:30.5 50 5 3C391 C4 9425 [0] [10]
11:58:25.5 - 12:03:20.5 51 6 3C391 C5 9725 [0] [10]
12:03:15.5 - 12:08:10.0 52 7 3C391 C6 9701 [0] [10]
12:08:05.0 - 12:12:59.0 53 8 3C391 C7 9725 [0] [10]
12:13:29.0 - 12:14:48.0 54 1 J1822-0938 2600 [0] [10]
12:15:18.0 - 12:20:07.5 55 2 3C391 C1 9425 [0] [10]
12:20:02.5 - 12:24:57.0 56 3 3C391 C2 9750 [0] [10]
12:24:51.5 - 12:29:46.5 57 4 3C391 C3 9750 [0] [10]
12:29:41.5 - 12:34:36.5 58 5 3C391 C4 9725 [0] [10]
12:34:31.5 - 12:39:26.0 59 6 3C391 C5 9725 [0] [10]
12:39:19.5 - 12:44:15.5 60 7 3C391 C6 9750 [0] [10]
12:44:10.5 - 12:49:04.5 61 8 3C391 C7 9750 [0] [10]
12:49:34.9 - 12:50:53.0 62 1 J1822-0938 2600 [0] [10]
12:51:24.0 - 12:56:12.5 63 2 3C391 C1 9425 [0] [10]
12:56:07.5 - 13:01:02.0 64 3 3C391 C2 9000 [0] [10]
13:00:57.0 - 13:05:51.5 65 4 3C391 C3 9750 [0] [10]
13:05:46.5 - 13:10:41.5 66 5 3C391 C4 9750 [0] [10]
13:10:36.5 - 13:15:31.0 67 6 3C391 C5 9725 [0] [10]
13:15:25.9 - 13:20:20.5 68 7 3C391 C6 9750 [0] [10]
13:20:15.5 - 13:25:10.0 69 8 3C391 C7 9000 [0] [10]
13:25:40.0 - 13:26:57.5 70 1 J1822-0938 2600 [0] [10]
13:27:28.0 - 13:32:16.5 71 2 3C391 C1 9425 [0] [10]
13:32:10.5 - 13:37:06.0 72 3 3C391 C2 9750 [0] [10]
13:37:01.0 - 13:41:55.5 73 4 3C391 C3 9750 [0] [10]
13:41:50.5 - 13:46:45.5 74 5 3C391 C4 9750 [0] [10]
13:46:40.5 - 13:51:35.0 75 6 3C391 C5 9725 [0] [10]
13:51:30.0 - 13:56:24.5 76 7 3C391 C6 9750 [0] [10]
13:56:19.5 - 14:01:14.0 77 8 3C391 C7 9750 [0] [10]
14:01:44.0 - 14:03:01.5 78 1 J1822-0938 2024 [0] [10]
14:03:33.0 - 14:08:21.0 79 2 3C391 C1 8900 [0] [10]
14:08:14.5 - 14:13:10.5 80 3 3C391 C2 9750 [0] [10]
14:13:05.3 - 14:18:00.5 81 4 3C391 C3 9750 [0] [10]
14:17:55.5 - 14:22:50.0 82 5 3C391 C4 9350 [0] [10]
14:22:45.0 - 14:27:39.5 83 6 3C391 C5 9000 [0] [10]
14:27:34.5 - 14:32:29.0 84 7 3C391 C6 8595 [0] [10]
14:32:24.0 - 14:37:18.5 85 8 3C391 C7 7590 [0] [10]
14:37:48.0 - 14:39:05.5 86 1 J1822-0938 1848 [0] [10]
14:39:36.0 - 14:44:24.5 87 2 3C391 C1 7337 [0] [10]
14:44:18.5 - 14:49:14.0 88 3 3C391 C2 7568 [0] [10]
14:49:09.0 - 14:54:04.0 89 4 3C391 C3 7590 [0] [10]
14:53:59.0 - 14:58:54.5 90 5 3C391 C4 7527 [0] [10]
14:58:48.5 - 15:03:43.0 91 6 3C391 C5 7568 [0] [10]
15:03:38.0 - 15:08:32.5 92 7 3C391 C6 7590 [0] [10]
15:08:27.5 - 15:13:22.0 93 8 3C391 C7 7590 [0] [10]
15:13:51.0 - 15:15:09.0 94 1 J1822-0938 1680 [0] [10]
15:15:40.0 - 15:20:28.5 95 2 3C391 C1 7337 [0] [10]
15:20:22.5 - 15:25:18.0 96 3 3C391 C2 7568 [0] [10]
15:25:12.0 - 15:30:08.0 97 4 3C391 C3 7590 [0] [10]
15:30:01.5 - 15:34:57.5 98 5 3C391 C4 7564 [0] [10]
15:34:52.5 - 15:39:47.0 99 6 3C391 C5 7260 [0] [10]
15:39:42.0 - 15:44:36.5 100 7 3C391 C6 6930 [0] [10]
15:44:31.5 - 15:49:26.0 101 8 3C391 C7 6930 [0] [10]
15:49:55.0 - 15:51:13.5 102 1 J1822-0938 1088 [0] [10]
15:54:52.0 - 16:00:11.5 103 9 J0319+4130 8768 [0] [10]
(nRows = Total number of rows per scan)
Fields: 10
ID Code Name RA Decl Epoch SrcId nRows
0 N J1331+3030 13:31:08.287984 +30.30.32.95886 J2000 0 31964
1 J J1822-0938 18:22:28.704200 -09.38.56.83501 J2000 1 39733
2 NONE 3C391 C1 18:49:24.244000 -00.55.40.58001 J2000 2 105580
3 NONE 3C391 C2 18:49:29.149001 -00.57.48.00001 J2000 3 110533
4 NONE 3C391 C3 18:49:19.339000 -00.57.48.00001 J2000 4 110331
5 NONE 3C391 C4 18:49:14.434001 -00.55.40.58001 J2000 5 110862
6 NONE 3C391 C5 18:49:19.339000 -00.53.33.16000 J2000 6 110546
7 NONE 3C391 C6 18:49:29.149001 -00.53.33.16000 J2000 7 109884
8 NONE 3C391 C7 18:49:34.054000 -00.55.40.58001 J2000 8 107178
9 Z J0319+4130 03:19:48.160102 +41.30.42.10305 J2000 9 8768
Spectral Windows: (1 unique spectral windows and 1 unique polarization setups)
SpwID Name #Chans Frame Ch1(MHz) ChanWid(kHz) TotBW(kHz) Corrs
0 Subband:0 64 TOPO 4536.000 2000.000 128000.0 RR RL LR LL
Sources: 10
ID Name SpwId RestFreq(MHz) SysVel(km/s)
0 J1331+3030 0 - -
1 J1822-0938 0 - -
2 3C391 C1 0 - -
3 3C391 C2 0 - -
4 3C391 C3 0 - -
5 3C391 C4 0 - -
6 3C391 C5 0 - -
7 3C391 C6 0 - -
8 3C391 C7 0 - -
9 J0319+4130 0 - -
Antennas: 26:
ID Name Station Diam. Long. Lat. Offset from array center (m) ITRF Geocentric coordinates (m)
East North Elevation x y z
0 ea01 W09 25.0 m -107.37.25.2 +33.53.51.0 -521.9407 -332.7782 -1.1977 -1601710.017000 -5042006.928200 3554602.355600
1 ea02 E02 25.0 m -107.37.04.4 +33.54.01.1 9.8247 -20.4292 -2.7808 -1601150.059500 -5042000.619800 3554860.729400
2 ea03 E09 25.0 m -107.36.45.1 +33.53.53.6 506.0591 -251.8666 -3.5832 -1600715.948000 -5042273.187000 3554668.184500
3 ea04 W01 25.0 m -107.37.05.9 +33.54.00.5 -27.3562 -41.3030 -2.7418 -1601189.030140 -5042000.493300 3554843.425700
4 ea05 W08 25.0 m -107.37.21.6 +33.53.53.0 -432.1158 -272.1493 -1.5032 -1601614.091000 -5042001.655700 3554652.509300
5 ea07 N06 25.0 m -107.37.06.9 +33.54.10.3 -54.0667 263.8720 -4.2292 -1601162.593200 -5041829.000000 3555095.890500
6 ea08 N01 25.0 m -107.37.06.0 +33.54.01.8 -30.8810 -1.4664 -2.8597 -1601185.634945 -5041978.156586 3554876.424700
7 ea09 E06 25.0 m -107.36.55.6 +33.53.57.7 236.9058 -126.3369 -2.4443 -1600951.588000 -5042125.911000 3554773.012300
8 ea11 E04 25.0 m -107.37.00.8 +33.53.59.7 102.8046 -63.7684 -2.6412 -1601068.791200 -5042051.910200 3554824.835300
9 ea12 E08 25.0 m -107.36.48.9 +33.53.55.1 407.8394 -206.0057 -3.2252 -1600801.916000 -5042219.371000 3554706.449900
10 ea13 N07 25.0 m -107.37.07.2 +33.54.12.9 -61.1040 344.2335 -4.6144 -1601155.635800 -5041783.843000 3555162.374100
11 ea14 E05 25.0 m -107.36.58.4 +33.53.58.8 164.9788 -92.8032 -2.5268 -1601014.462000 -5042086.252000 3554800.799800
12 ea15 W06 25.0 m -107.37.15.6 +33.53.56.4 -275.8288 -166.7451 -2.0590 -1601447.198000 -5041992.502500 3554739.687600
13 ea16 W02 25.0 m -107.37.07.5 +33.54.00.9 -67.9687 -26.5614 -2.7175 -1601225.255200 -5041980.383590 3554855.675000
14 ea17 W07 25.0 m -107.37.18.4 +33.53.54.8 -349.9866 -216.7507 -1.7978 -1601526.386100 -5041996.840100 3554698.327400
15 ea18 N09 25.0 m -107.37.07.8 +33.54.19.0 -77.4352 530.6274 -5.5867 -1601139.485500 -5041679.036000 3555316.532800
16 ea19 W04 25.0 m -107.37.10.8 +33.53.59.1 -152.8599 -83.8054 -2.4614 -1601315.893000 -5041985.320170 3554808.304600
17 ea20 N05 25.0 m -107.37.06.7 +33.54.08.0 -47.8454 192.6015 -3.8723 -1601168.786100 -5041869.054000 3555036.936000
18 ea21 E01 25.0 m -107.37.05.7 +33.53.59.2 -23.8638 -81.1510 -2.5851 -1601192.467800 -5042022.856800 3554810.438800
19 ea22 N04 25.0 m -107.37.06.5 +33.54.06.1 -42.5986 132.8623 -3.5431 -1601173.953700 -5041902.660400 3554987.536500
20 ea23 E07 25.0 m -107.36.52.4 +33.53.56.5 318.0523 -164.1848 -2.6960 -1600880.570000 -5042170.388000 3554741.457400
21 ea24 W05 25.0 m -107.37.13.0 +33.53.57.8 -210.0944 -122.3885 -2.2581 -1601377.008000 -5041988.665500 3554776.393400
22 ea25 N02 25.0 m -107.37.06.2 +33.54.03.5 -35.6245 53.1806 -3.1345 -1601180.861480 -5041947.453400 3554921.628700
23 ea26 W03 25.0 m -107.37.08.9 +33.54.00.1 -105.3429 -51.7191 -2.6054 -1601265.151700 -5041982.533050 3554834.856300
24 ea27 E03 25.0 m -107.37.02.8 +33.54.00.5 50.6647 -39.4832 -2.7249 -1601114.365500 -5042023.153700 3554844.945600
25 ea28 N08 25.0 m -107.37.07.5 +33.54.15.8 -68.9057 433.1889 -5.0602 -1601147.940400 -5041733.837000 3555235.956000
##### End Task: listobs #####
##########################################
Note that the antenna IDs (which are numbered sequentially up to the total number of antennas in the array; 0 through 25 in this instance) do not correspond to the actual antenna names (ea01 through ea28; these numbers correspond to those painted on the side of the dishes). During our data reduction, we can refer to the antennas using either convention; antenna='22' would correspond to ea25, whereas antenna='ea22' would correspond to ea22. Note that the antenna numbers in the observer log correspond to the actual antenna names, i.e. the 'ea??' numbers given in listobs.
Both to get a sense of the array, as well as identify an antenna for later use in calibration, use the task plotants. In general, for calibration purposes, one would like to select an antenna that is close to the center of the array (and that is not listed in the operator's log as having had problems!).
# In CASA
plotants(vis='3c391_ctm_mosaic_10s_spw0.ms',figfile='plotants_3c391_antenna_layout.png')
clearstat() # This removes the table lock generated by plotants in script mode
Examining and Editing the Data
It is always a good idea, particularly with a new system like the EVLA, to examine the data. Moreover, from the observer's log, we already know that one antenna will need to be flagged because it does not have a C-band receiver. Start by flagging data known to be bad, then examine the data.
In its current operation, it is common to insert a dummy scan as the first scan. (From the listobs output above, one may have noticed that the first scan is less than 1 minute long.) This first scan can safely be deleted.
# In CASA
flagdata(vis='3c391_ctm_mosaic_10s_spw0.ms', flagbackup=T,
mode='manual', scan='1')
- flagbackup=T : A comment is warranted on the setting of flagbackup (here set to T or True). If set to True, flagdata will save a copy of the existing set of flags before entering any new flags. The setting of flagbackup is therefore a matter of some taste. One could choose not to save any flags or only save "major" flags, or one could save every flag. (One of the authors of this document was glad that flagbackup was set to True as he recently ran flagdata with a typo in one of the entries.)
- mode='manualflag' : Specific data are going to be selected to be edited.
- scan='1' is chosen to select only the first scan. Note that scan expects an entry in the form of a string. (scan=1 would generate an error.)
If satisfied with the inputs, run this task. The initial display in the logger will include
##########################################
##### Begin Task: flagdata #####
flagdata(vis="3c391_ctm_mosaic_10s_spw0.ms",mode="manual",autocorr=False,inpfile="",
reason="any",spw="",field="",antenna="",uvrange="",
timerange="",correlation="",scan="1",intent="",array="",
observation="",feed="",clipminmax=[],datacolumn="DATA",clipoutside=True,
channelavg=False,clipzeros=False,quackinterval=1.0,quackmode="beg",quackincrement=False,
tolerance=0.0,addantenna="",lowerlimit=0.0,upperlimit=90.0,ntime="scan",
combinescans=False,timecutoff=4.0,freqcutoff=3.0,timefit="line",freqfit="poly",
maxnpieces=7,flagdimension="freqtime",usewindowstats="none",halfwin=1,winsize=3,
timedev="",freqdev="",timedevscale=5.0,freqdevscale=5.0,spectralmax=1000000.0,
spectralmin=0.0,extendpols=True,growtime=50.0,growfreq=50.0,growaround=False,
flagneartime=False,flagnearfreq=False,minrel=0.0,maxrel=1.0,minabs=0,
maxabs=-1,spwchan=False,spwcorr=False,basecnt=False,action="apply",
display="",flagbackup=True,savepars=False,cmdreason="",outfile="")
Backup original flags before applying new flags
Table type is Measurement Set
Creating new backup flag file called flagdata_1
Table type is Measurement Set
Manual mode is active
Parsing the parameters for the manual mode
Initializing the agents
Manual autocorr is 0
There are 1 valid agents in list
Running the agentflagger tool
------------------------------------------------------------------------------------
Chunk = 1 [progress: 100%], Observation = 0, Array = 0, Scan = 1, Field = 0 (J1331+3030), Spw = 0, Channels = 64, Corrs = [ RR RL LR LL ], Total Rows = 650
Manual => Data flagged so far 100%
====================================================================================
=> Percentage of data flagged in table selection: 100%
=> Writing flags to the MS
##### End Task: flagdata #####
##########################################
which indicates that, among other things, the flags that existed in the data set prior to this run will be saved to another file called flagdata_1. Should one ever desire to revert to the data prior to this run, the task flagmanager could be used. Also note that the values of all the task parameters (explicit or hidden) are given at the start of the task listing.
From the observer's log, we know that antenna ea13 does not have a C band receiver and antenna ea15 had some corrupted data, so they should be flagged as well. The parameters are similar as before.
# In CASA
flagdata(vis='3c391_ctm_mosaic_10s_spw0.ms', flagbackup=T, mode='manual',
antenna='ea13,ea15')
- antenna='ea13,ea15' : Once again, this parameter requires a string input. Remember that antenna='ea13' and 'antenna='13' are not the same antenna. (See the discussion after our call to listobs above.)
Finally, it is common for the array to require a small amount of time to "settle down" at the start of a scan. Consequently, it has become standard practice to edit out the initial samples from the start of each scan.
# In CASA
flagdata(vis='3c391_ctm_mosaic_10s_spw0.ms', mode='quack',
quackinterval=10.0, quackmode='beg')
- mode='quack' : Quack is another mode in which the same edit will be applied to all scans for all baselines.
- quackmode='beg' : In this case, data from the start of each scan will be flagged. Other options include flagging data at the end of the scan.
- quackinterval=10 : In this data set, the sampling time is 10 seconds, so this choice flags the first sample from all scans on all baselines.
Having now done some basic editing of the data, based in part on a priori information, it is time to look at the data to determine if there are any other obvious problems. One task to examine the data themselves is plotms.
# In CASA
clearstat() # This removes any existing table locks generated by flagdata
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms', selectdata=True, field='0')
- selectdata=T : One can choose to plot only subsets of the data.
- field='0' : The entire dataset is rather large, and different sources have very different amplitudes, so it is advisable to start by loading a subset of the data. One can later loop through the different fields (i.e. sources) and spectral windows using the GUI interface.
In this case, many other values have been left to defaults, but it is possible to select them from within the plotms GUI.
plotms should produce a GUI, with the default view being to show the visibility amplitude as a function of time. The figure at right shows the result of running plotms without the field selection discussed above (using field=' ' ).
plotms allows one to select and view the data in many ways. Across the top of the left panel are a set of tabs labeled 'Plots', 'Flagging', 'Tools', 'Annotator', and 'Options'. If one selects the 'Flagging' tab, the option is to 'Extend flags'. Thus, even though plotms was started with extendflag=F, if one decides that it does make sense to extend the flags, one can still do so here.
In the default view, the 'Plots' tab is visible, and there are a number of tabs running down the side of the left hand panel, including 'Data', 'Axes', 'Trans', 'Cache', 'Display', 'Canvas', and 'Export'. Once again, one can make changes on the fly. Thus, supposing that one wants to save a hard copy, even if plotms was started with plotfile=' ', one can select 'Export' and enter a file name in which to save a copy of a plot.
One should spend several minutes displaying the data in various formats. For instance, one could select the 'Data' tab and specify field 0 (source J1331+3030, a.k.a. 3C 286) to display data associated with the amplitude calibrator, then select the 'Axes' tab and change the x axis to be UVDist (baseline length, in meters), and plot the data. The result should be that of the first thumbnail image shown below. The amplitude distribution is relatively constant as a function of u-v distance or baseline length (i.e., [math]\displaystyle{ \sqrt{u^2+v^2} }[/math]). From the various lectures, one should recognize that a relatively constant visibility amplitude as a function of baseline length means that the source is very nearly a point source. (The Fourier transform of a constant is a delta function, a.k.a. a point source.)
By contrast, if one selects field 3 (one of the 3C 391 fields) in the 'Data' tab and plots these data, one sees a visibility function that falls rapidly with increasing baseline length. Such a visibility function indicates a highly resolved source. By noting the baseline length at which the visibility function falls to some fiducial value (e.g., 1/2 of its peak value), one can obtain a rough estimate of the angular scale of the source. (From the lectures, angular scale [in radians] ~ 1/baseline [in wavelengths]. To plot baseline length in wavelengths rather than meters, one needs to select UVwave as the x-axis in the plotms GUI.)
As a general data editing and examination strategy, at this stage in the data reduction process, one wants to focus on the calibrators. The data reduction strategy is to determine various corrections from the calibrators, then apply these correction factors to the science data. The 3C 286 data look relatively clean. There are no wildly egregious data (e.g., amplitudes that are 100,000x larger than the rest of the data). One may notice that there are antenna-to-antenna variations (under the 'Display' tab, select 'Colorize by Antenna1'). These antenna-to-antenna variations are acceptable, that's what calibration will help determine.
One final useful plot we will make is a "datastream" plot of the antenna2 in a baseline for the data versus ea01. This shows (assuming ea01 is there the entire run) when various antennas drop out.
# In CASA
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='',correlation='RR,LL',
timerange='',antenna='ea01',spw='0:31',
xaxis='time',yaxis='antenna2',
plotrange=[-1,-1,0,26],coloraxis='field')
See the plot to right (after fiddling with the symbol sizes to improve visibility). From this display you can see that antenna 3 (ea04) is missing the last scan on 3C84 (which will have some implications later on), antennas 1,6,13 (ea02,ea08,ea16) have some missing blocks of time in the middle of the run, and 23 (ea26) is missing a scan or two near the end.
Calibrating the Data
It is now time to begin calibrating the data. The general data reduction strategy is to derive a series of scaling factors or corrections from the calibrators, which are then collectively applied to the science data. For much more discussion of the philosophy, strategy, and implementation of calibration of synthesis data within CASA, see Synthesis Calibration in the CASA Reference Manual.
Recall that the observed visibility [math]\displaystyle{ V^{\prime} }[/math] between two antennas [math]\displaystyle{ (i,j) }[/math] is related to the "true" visibility [math]\displaystyle{ V }[/math] by
[math]\displaystyle{ V^{\prime}_{i,j}(u,v,f) = b_{ij}(t)\,[B_i(f,t) B^{*}_j(f,t)]\,g_i(t) g_j(t)\,V_{i,j}(u,v,f)\,e^{i [\theta_i(t) - \theta_j(t)]} }[/math]
Here, for generality, we show the visibility as a function of frequency [math]\displaystyle{ f }[/math] and spatial wavenumbers [math]\displaystyle{ u }[/math] and [math]\displaystyle{ v }[/math]. The other terms are
- [math]\displaystyle{ g_i }[/math] and [math]\displaystyle{ \theta_i }[/math] are the amplitude and phase portions of what is commonly termed the complex gain. They are shown separately here because they are usually determined separately. For completeness, these are shown as a function of time [math]\displaystyle{ t }[/math] to indicate that they can change with temperature, atmospheric conditions, etc.
- [math]\displaystyle{ B_i }[/math] is the complex bandpass, the instrumental response as a function of frequency, [math]\displaystyle{ f }[/math]. As shown here, the bandpass may also vary as a function of time.
- [math]\displaystyle{ b(t) }[/math] is the often-neglected baseline term. It can be important to include for the highest dynamic range images or shortly after a configuration change at the [E]VLA, when antenna positions may not be known well.
Strictly, the equation above is a simplification of a more general measurement equation formalism, but it is a useful simplification in many cases.
A priori Antenna Position Corrections
As mentioned in the observing log above, antennas ea10, ea12, and ea22 do not have good baseline positions. Antenna ea10 was not in the array, but, for the other two antennas, any improved baseline positions need to be incorporated. The importance of this step is that the visibility function is a function of [math]\displaystyle{ u }[/math] and [math]\displaystyle{ v }[/math]. If the baseline positions are incorrect, then [math]\displaystyle{ u }[/math] and [math]\displaystyle{ v }[/math] will be calculated incorrectly, and there will be errors in the image. (These corrections could also be determined later by a baseline-based calibration incorporating the [math]\displaystyle{ b_{ij} }[/math] term from the equation above, but since they are known a priori it makes sense to incorporate them now.)
The calculations are inserted via gencal which (for CASA 3.4 and later) allows automated lookup of the corrections. To see how to calculate corrections manually, go to the EVLA/VLA Baseline Corrections site.
# In CASA
gencal(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.antpos',caltype='antpos')
In the logger you can see the corrections reported:
##########################################
##### Begin Task: gencal #####
gencal(vis="3c391_ctm_mosaic_10s_spw0.ms",caltable="3c391_ctm_mosaic_10s_spw0.antpos",caltype="antpos",spw="",
antenna="",pol="",parameter=[])
Opening MS: 3c391_ctm_mosaic_10s_spw0.ms for calibration.
Initializing nominal selection to the whole MS.
Determine antenna position offests from the baseline correction database
offsets for antenna ea01 : 0.00000 0.00300 0.00000
offsets for antenna ea02 : -0.00080 0.00000 0.00000
offsets for antenna ea03 : -0.00280 0.00000 0.00000
offsets for antenna ea05 : 0.00000 0.00280 0.00000
offsets for antenna ea11 : 0.00090 0.00000 0.00000
offsets for antenna ea12 : -0.01000 0.00450 -0.00170
offsets for antenna ea13 : 0.00000 -0.00080 0.00000
offsets for antenna ea17 : -0.00120 0.00000 0.00000
offsets for antenna ea18 : 0.00040 -0.00080 0.00040
offsets for antenna ea22 : -0.02570 0.00270 -0.01900
offsets for antenna ea23 : -0.00140 0.00000 0.00000
offsets for antenna ea24 : -0.00150 0.00000 0.00000
offsets for antenna ea26 : -0.00190 0.00000 0.00210
offsets for antenna ea27 : 0.00000 0.00190 -0.00160
Beginning specifycal-----------------------
Creating KAntPos Jones table from specified parameters.
Writing solutions to table: 3c391_ctm_mosaic_10s_spw0.antpos
##### End Task: gencal #####
##########################################
This corresponds to what is found in the database for 2010:
; 2010 BASELINE CORRECTIONS IN METERS
;ANT
;MOVED OBSDATE Put_In_ MC(IAT) ANT PAD Bx By Bz
;
JAN27 FEB12 FEB21 01:57 11 E04 0.0000 0.0000 0.0000
JAN27 FEB12 FEB21 01:57 26 W03 -0.0170 0.0204 0.0041
MAR24 MAR25 MAR26 18:28 17 W07 -0.0061 -0.0069 -0.0055
APR21 MAY02 MAY04 23:25 12 E08 -0.0072 0.0045 -0.0017
MAR09 MAY02 MAY04 23:25 22 N04 -0.0220 0.0040 -0.0190
JUN08 JUN20 JUN22 03:00 10 N03 0.0046 -0.0196 0.0090
JUL17 JUL18 21:44 1 W09 0.0000 0.0030 0.0000
JUL17 JUL18 21:44 2 E02 -0.0008 0.0000 0.0000
JUL17 JUL18 21:44 3 E09 -0.0028 0.0000 0.0000
JUL17 JUL18 21:44 5 W08 0.0000 0.0028 0.0000
JUL01 JUL17 JUL18 21:44 6 N06 0.0022 0.0010 0.0059
JUL17 JUL18 21:44 10 N03 0.0008 0.0030 -0.0014
JUL17 JUL18 21:44 11 E04 0.0009 0.0000 0.0000
JUL17 JUL18 21:44 12 E08 -0.0028 0.0000 0.0000
JUL17 JUL18 21:44 13 N07 0.0000 -0.0008 0.0000
JUL17 JUL18 21:44 17 W07 -0.0012 0.0000 0.0000
JUL17 JUL18 21:44 18 N09 0.0004 -0.0008 0.0004
JUL17 JUL18 21:44 22 N04 -0.0037 -0.0013 0.0000
JUL17 JUL18 21:44 23 E07 -0.0014 0.0000 0.0000
JUL17 JUL18 21:44 24 W05 -0.0015 0.0000 0.0000
JUL17 JUL18 21:44 26 W03 -0.0019 0.0000 0.0021
JUL17 JUL18 21:44 27 E03 0.0000 0.0019 -0.0016
AUG05 SEP15 SEP16 00:11 07 E05 0.0087 0.0137 0.0000
SEP13 SEP15 SEP16 00:11 08 N10 0.0098 -0.0063 0.0059
SEP13 SEP15 SEP16 00:11 10 N14 0.0124 -0.0050 0.0110
SEP14 SEP15 SEP16 00:11 13 N12 0.0020 -0.0060 -0.0077
SEP13 SEP15 SEP16 00:11 18 N16 -0.0035 0.0000 -0.0027
SEP13 SEP15 SEP16 00:11 20 N18 0.0044 -0.0020 0.0000
OCT04 OCT06 OCT11 05:03 1 W18 -0.0087 0.0077 -0.0041
OCT05 OCT06 OCT11 05:03 3 E18 -0.0131 -0.0143 0.0099
OCT04 OCT06 OCT11 05:03 4 W10 0.0041 0.0032 0.0005
OCT04 OCT06 OCT11 05:03 7 E14 0.0027 0.0154 0.0049
OCT05 OCT06 OCT11 05:03 17 W14 -0.0141 0.0095 -0.0046
OCT04 OCT06 OCT11 05:03 23 E16 0.0044 0.0045 -0.0076
OCT05 OCT06 OCT11 05:03 24 W16 -0.0017 0.0004 0.0038
OCT05 OCT06 OCT11 05:03 27 E10 0.0039 0.0188 -0.0060
OCT06 OCT07 OCT12 20:12 21 E12 -0.0125 -0.0140 -0.0100
OCT20 OCT22 OCT23 19:54 14 W12 0.0191 -0.0126 0.0032
OCT22 OCT23 19:54 21 E12 0.0196 -0.0062 0.0051
DEC01 DEC04 DEC08 20:28 26 W02 -0.0130 0.0265 0.0187
Flux Density Scale
The next step is to provide a flux density value for the amplitude calibrator J1331+3030 (a.k.a. 3C 286). For the VLA, the ultimate flux density scale at most frequencies was set by 3C 295, which was then transferred to a small number of "primary flux density calibrators," including 3C 286. For the EVLA, at the time of this writing, the flux density scale at most frequencies will be determined from WMAP observations of the planet Mars, in turn then transferred to a small number of primary flux density calibrators. Thus, the procedure is to assume that the flux density of a primary calibrator source is known and, by comparison with the observed data for that calibrator, determine the [math]\displaystyle{ g_i }[/math] values.
To start, let's find the available calibrator models with setjy and the option listmodels=True:
# In CASA
setjy(vis='3c391_ctm_mosaic_10s_spw0.ms', listmodels=T)
This command will show all available calibrator models:
No candidate modimages matching '*.im* *.mod*' found in . Candidate modimages (*) in /usr/lib64/casapy/release/4.2.0/data/nrao/VLA/CalModels: 3C138_A.im 3C138_S.im 3C147_K.im 3C147_X.im 3C286_Q.im 3C48_C.im 3C48_U.im 3C138_C.im 3C138_U.im 3C147_L.im 3C286_A.im 3C286_S.im 3C48_K.im 3C48_X.im 3C138_K.im 3C138_X.im 3C147_Q.im 3C286_C.im 3C286_U.im 3C48_L.im README 3C138_L.im 3C147_A.im 3C147_S.im 3C286_K.im 3C286_X.im 3C48_Q.im 3C138_Q.im 3C147_C.im 3C147_U.im 3C286_L.im 3C48_A.im 3C48_S.im
Since any image could be a potential calibrator model setjy will list all *.im and *.mod images in the working directory. In addition, it will list all models that are provided by NRAO with the CASA package, and they will be picked by their names. We will be using the C-band EVLA standard model for 3C286 which is aptly named '3C286_C.im':
# In CASA
setjy(vis='3c391_ctm_mosaic_10s_spw0.ms',field='J1331+3030',modimage='3C286_C.im',
standard='Perley-Butler 2010',usescratch=False,scalebychan=True,spw='')
- field='J1331+3030' : Clearly one has to specify what the flux density calibrator is, otherwise all sources will be assumed to have the same flux density.
- modimage='3C286_C.im' : Although above, from plotms, it was estimated that 3C 286 is roughly a point source, depending upon the frequency and configuration, the source may be slightly resolved. Fiducial model images have been determined from a painstaking set of observations, and, if one is available, it should be used to compensate for slight resolution effects. In this case, spectral window 0 (at 4.536 GHz) is in the C band, so the C-band model image is used.
- standard='Perley-Butler 2010' : Periodically, the flux density scale at the VLA was revised, updated, or expanded. The specified value represents the most recent determination of the flux density scale (by R. Perley and B. Butler in 2010); older scales can also be specified, and might be important if, for example, one was attempting to conduct a careful comparison with a previously published result.
- usescratch=False : We will NOT force the writing of the model visibilities to the MODEL_DATA scratch column, to save disk space.
- scalebychan=True : In order to take out the intrinsic spectral index of our flux density calibrator 3C286 when we use it as our bandpass calibrator, we let it calculate a flux density value per channel.
- spw=' ' : The original data contained two spectral windows. Having split off spectral window 0, it is not necessary to specify spw. Had the spectral window 0 not been split off, as has been done here, we might wish to specify the spectral window because, in this observation, the spectral windows were sufficiently separated that two different model images for 3C 286 would be appropriate; 3C286_C.im at 4.6 GHz and 3C286_X.im at 7.5 GHz. This would require two separate runs of setjy, one for each spectral window. If the spectral windows were much closer together, it might be possible to calibrate both using the same model.
In this case, a model image of a primary flux density calibrator exists. However, for some kinds of polarization calibration or in extreme situations (e.g., there are problems with the scan on the flux density calibrator), it can be useful or required to set the flux density of the source explicitly.
The output from setjy should look similar to the following.
##########################################
##### Begin Task: setjy #####
setjy(vis="3c391_ctm_mosaic_10s_spw0.ms",field="J1331+3030",spw="",selectdata=False,
timerange="",scan="",observation="",modimage="3C286_C.im",listmodels=False,
scalebychan=True,fluxdensity=-1,spix=0,reffreq="1GHz",standard="Perley-Butler 2010",
useephemdir=False,usescratch=False)
Opening MeasurementSet /Science/CASA_Guides/3C391_CASA4.1/3c391_ctm_mosaic_10s_spw0.ms
Using /Applications/CASA_4.1/CASA.app/Contents/data/nrao/VLA/CalModels/3C286_C.im for modimage.
Using channel dependent flux densities
Selected 31964 out of 845379 rows.
J1331+3030 (fld ind 0) spw 0 [I=7.8169, Q=0, U=0, V=0] Jy, (Perley-Butler 2010)
Using model image /Applications/CASA_4.1/CASA.app/Contents/data/nrao/VLA/CalModels/3C286_C.im
Scaling spw 0's model image by channel to I = [7.81694, 7.81481, 7.81267, 7.81054, 7.80841, 7.80628, 7.80416, 7.80203, 7.7999, 7.79778, 7.79566, 7.79354, 7.79142, 7.7893, 7.78718, 7.78507, 7.78295, 7.78084, 7.77873, 7.77662, 7.77451, 7.7724, 7.7703, 7.76819, 7.76609, 7.76398, 7.76188, 7.75978, 7.75769, 7.75559, 7.75349, 7.7514, 7.74931, 7.74721, 7.74512, 7.74303, 7.74095, 7.73886, 7.73677, 7.73469, 7.73261, 7.73053, 7.72845, 7.72637, 7.72429, 7.72221, 7.72014, 7.71807, 7.71599, 7.71392, 7.71185, 7.70978, 7.70772, 7.70565, 7.70359, 7.70152, 7.69946, 7.6974, 7.69534, 7.69328, 7.69123, 7.68917, 7.68712, 7.68506] Jy (ch 0) for visibility prediction.
The model image's reference pixel is 0.00302169 arcsec from J1331+3030's phase center.
Will clear any existing model with matching field=J1331+3030 and spw=*
Clearing model records in MS header for selected fields.
J1331+3030 (id = 0) not found.
Selected 31964 out of 845379 rows.
##### End Task: setjy #####
##########################################
As set, the flux density scale is being calculated only for spectral window 0 (spw='0' ). The flux density in each Stokes (IQUV) for the reference channel 0 is reported, followed by the I flux density in each channel of the spectral window that will be used to scale the data. This value is determined from an analytical formula for the spectrum of the source as a function of frequency; this value must be determined so that the flux density in the image can be scaled to it, as it is unlikely that the observation was taken at exactly the same frequency as the model image.
Initial Phase Calibration
Before solving for the bandpass, we will do an initial phase calibration. Depending upon frequency and configuration, there could be gain variations between the different scans of the bandpass calibrator, particularly if the scans happen at much different elevations. One can solve for an initial set of antenna-based gains, which will later be discarded, in order to moderate the effects of variations from scan to scan on the bandpass calibrator. While amplitude variations will have little effect on the bandpass solutions, it is important to solve for any phase variations with time to prevent decorrelation when vector averaging the data in computing the bandpass solutions.
We solve for phase versus time for the central channels on our three calibrators:
# In CASA
gaincal(vis='3c391_ctm_mosaic_10s_spw0.ms', caltable='3c391_ctm_mosaic_10s_spw0.G0all',
field='0,1,9', refant='ea21', spw='0:27~36',
gaintype='G',calmode='p', solint='int',
minsnr=5, gaintable=['3c391_ctm_mosaic_10s_spw0.antpos'])
- caltable='3c391_ctm_mosaic_10s_spw0.G0all' : The gain solutions will be stored in an external table.
- field='0,1,9' : Specify the calibrators. We will use this opportunity to inspect solutions for all calibrators to weed out bad data.
- refant='ea21' : Earlier, by looking at the output from plotants, a reference antenna near the center of the array was noted. Here is the first time that that choice will be used. Strictly, all of the gain corrections derived will be relative to this reference antenna.
- spw='0:27~36' : One wants to choose a subset of the channels from which to determine the gain corrections. These should be near the center of the band, and there should be enough channels chosen so that a reasonable signal-to-noise ratio can be obtained. (See the output of plotms above.) Particularly at lower frequencies where RFI can manifest itself, one should choose RFI-free frequency channels. Also note that, even though these data have only a single spectral window, the syntax requires specifying the spectral window in order to specify the spectral channels.
- gaintype='G' : Compute G solutions, one per antenna per spw per polarization per solution interval
- calmode='p' : Solve for only the phase portion of the gain.
- solint='int' : One wants to be able to track the phases, so a short solution interval is chosen. (A single integration time or 10 seconds for this case)
- minsnr=5 : One probably wants to restrict the solutions to be at relatively high signal-to-noise ratios, although this parameter may need to be varied depending upon the source and frequency.
- gaintable=['3c391_ctm_mosaic_10s_spw0.antpos'] : Having produced antenna position corrections, they should now be applied.
To really see what is going on, we use plotcal to inspect the solutions for a single antenna at a time, iterating through each antenna in sequence, starting with the R polarization:
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G0all',xaxis='time',yaxis='phase',
poln='R',iteration='antenna',plotrange=[-1,-1,-180,180])
You use the Next button on the GUI to advance the displayed antenna.
NOTE: Sometimes plotcal will "lock" a table and/or keep it in the table cache beyond the end of plotting. This can hang up further use of that table, or cause errors if you delete the table (outside of CASA) and want to re-create it. To deal with that issue, simply close the plotcal GUI using the Quit button when you are done looking at the plot.
Antennas that have been flagged will show a blank plot, as there are no solutions for these antennas. For most antennas, we see a fairly smooth variation with time, so we expect to be able to calibrate our data nicely. However, when you get top ea05, ote the phase jumps where it appears to be bouncing between two states. We can plot this antenna separately (see the figure to the right):
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G0all',xaxis='time',yaxis='phase',antenna='ea05',
poln='R',iteration='antenna',plotrange=[-1,-1,-180,180],figfile='plotcal_3c391-G0all-phase-R-ea05.png')
We see the same thing for the L polarization solutions:
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G0all',
xaxis='time', yaxis='phase', poln='L',
iteration='antenna', plotrange=[-1,-1,-180,180])
Antennas other than ea05 look OK.
We will not be able to transfer calibration for antenna ea05 so we will delete it from the data:
# In CASA
flagdata(vis='3c391_ctm_mosaic_10s_spw0.ms',
flagbackup=T, mode='manual', antenna='ea05')
For the following bandpass solution we need only solve for our bandpass calibrator, and we will do so now after flagging:
# In CASA
gaincal(vis='3c391_ctm_mosaic_10s_spw0.ms', caltable='3c391_ctm_mosaic_10s_spw0.G0',
field='J1331+3030', refant='ea21', spw='0:27~36', calmode='p', solint='int',
minsnr=5, gaintable=['3c391_ctm_mosaic_10s_spw0.antpos'])
You can inspect this with plotcal as we did above. For example, plot R for the first block of 3C286 data only
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G0',
xaxis='time',yaxis='phase',poln='R',field='J1331+3030',iteration='antenna',
plotrange=[-1,-1,-180,180],timerange='08:02:00~08:17:00')
You can do the same for L if you like.
Delay Calibration
The first stage of bandpass calibration involves solving for the antenna-based delays which put a phase ramp versus frequency channel in each spectral window. The K gain type in gaincal solves for the relative delays of each antenna relative to the refant (so be sure you pick one that is there for this entire scan and good). This is not a full global delay, but gives one value per spw per polarization.
# In CASA
gaincal(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.K0',
field='J1331+3030',refant='ea21',spw='0:5~58',gaintype='K',
solint='inf',combine='scan',minsnr=5,
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.G0'])
- field='J1331+3030' : For the bandpass calibrator
- refant='ea21' : Delays will be relative to this antenna, make sure it is there!
- spw='0:5~58' : Widest possible frequency range in the spw, avoiding edge channels
- gaintype='K' : Compute K solutions, one per antenna per spw per polarization per solution interval
- solint='inf',combine='scan' : Only need one solution averaged over all times and scans
- minsnr=5 : One probably wants to restrict the solutions to be at relatively high signal-to-noise ratios, although this parameter may need to be varied depending upon the source and frequency.
- gaintable : Use the antpos and G0 tables.
We can plot these solutions (in nanoseconds) as a function of antenna:
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.K0',xaxis='antenna',yaxis='delay',
figfile='plotcal_3c391-K0-delay.png')
These are within about 4 nanoseconds, as expected for the EVLA early science observations.
Bandpass Calibration
In this step one solves for the complex bandpass, [math]\displaystyle{ B_i }[/math].
For the VLA, in its old continuum modes, this step could be skipped. With the EVLA, all data are spectral line, even if the science that one is conducting is continuum. Solving for the bandpass won't hurt for continuum data, and, for moderate or high dynamic range image, it is essential. To motivate the need for solving for the bandpass, consider the image to the right. It shows the right circularly polarized data (RR polarization) for the source J1331+3030, which will serve as the bandpass calibrator. The data are color coded by scan, and they are averaged over all baselines, as earlier plots from plotms indicated that the visibility data are nearly constant with baseline length. Ideally, the visibility data would be constant as a function of frequency as well. The variations with frequency are a reflection of the (slightly) different antenna bandpasses. (Exercise for the reader, reproduce this plot using plotms.)
Now form the bandpass, using the phase solutions just derived.
# In CASA
bandpass(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.B0',
field='J1331+3030',spw='',refant='ea21',solnorm=True,combine='scan',
solint='inf',bandtype='B',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.G0',
'3c391_ctm_mosaic_10s_spw0.K0'])
- caltable='3c391_ctm_mosaic_10s_spw0.B0' : Specify where to store the bandpass corrections.
- solnorm=T : Make sure that the average of the amplitudes of the bandpass corrections are normalized to unity (across the spw)
- solint='inf', combine='scan' : This observation contains multiple scans on the bandpass calibrator, J1331+3030. Because these are continuum observations, it is probably acceptable to combine all the scans and compute one bandpass correction per antenna, which is achieved by the combination of solint='inf' and combine='scan'. Had combine=' ', then there would have been a bandpass correction derived per scan, which might be necessary for the highest dynamic range spectral line observations.
- bandtype='B' : The bandpass solution will be derived on a channel-by-channel basis. There is an alternate, somewhat experimental option of bandtype='BPOLY' that will attempt to fit an n-th order polynomial to the bandpass.
- gaintable : Pre-apply antenna positions, phase solutions, and delays.
Once again, one can use plotcal to display the bandpass solutions. Note that in the plotcal inputs below, the amplitudes are being displayed as a function of frequency channel and, for compactness, subplot=221 is used to display multiple plots per page. One could use yaxis='phase' to view the phases as well. We use iteration='antenna' to step through separate plots for each antenna.
# In CASA
plotcal(caltable= '3c391_ctm_mosaic_10s_spw0.B0',poln='R',
xaxis='chan',yaxis='amp',field= 'J1331+3030',subplot=221,
iteration='antenna',figfile='plotcal_3c391-3C286-B0-R-amp.png')
#
plotcal(caltable= '3c391_ctm_mosaic_10s_spw0.B0',poln='L',
xaxis='chan',yaxis='amp',field= 'J1331+3030',subplot=221,
iteration='antenna',figfile='plotcal_3c391-3C286-B0-L-amp.png')
#
plotcal(caltable= '3c391_ctm_mosaic_10s_spw0.B0',poln='R',
xaxis='chan',yaxis='phase',field= 'J1331+3030',subplot=221,
iteration='antenna',plotrange=[-1,-1,-180,180],
figfile='plotcal_3c391-3C286-B0-R-phase.png')
#
plotcal(caltable= '3c391_ctm_mosaic_10s_spw0.B0',poln='L',
xaxis='chan',yaxis='phase',field= 'J1331+3030',subplot=221,
iteration='antenna',plotrange=[-1,-1,-180,180],
figfile='plotcal_3c391-3C286-B0-L-phase.png')
As expected, the bandpass phases (rightmost plots below) are relatively flat, with the slopes removed by the delay calibration. Residual excursions are on the order of a few degrees.
 |
 |
 |
 |
Gain Calibration
The next step is to derive corrections for the complex antenna gains, [math]\displaystyle{ g_i }[/math] and [math]\displaystyle{ \theta_i }[/math]. As discussed in the lectures and above, the absolute magnitude of the gain amplitudes [math]\displaystyle{ g_i }[/math] are determined by reference to a standard flux density calibrator. In order to determine the appropriate complex gains for the target source, one wants to observe a so-called phase calibrator that is much closer to the target, in order to minimize differences through the atmosphere (neutral and/or ionized) between the lines of sight to the phase calibrator and the target source. If we determine the relative gain amplitudes and phases for different antennas using the phase calibrator, we can later determine the absolute flux density scale by comparing the gain amplitudes [math]\displaystyle{ g_i }[/math] derived for 3C 286 with those derived for the phase calibrator. This will eventually be done using the task fluxscale. Since there is no such thing as absolute phase, we determine a zero phase by selecting a reference antenna for which the gain phase is defined to be zero.
In principle, one could determine the complex antenna gains for all sources with a single invocation of gaincal; for clarity here, two separate invocations will be used.
In the first step, we derive the appropriate complex gains [math]\displaystyle{ g_i }[/math] and [math]\displaystyle{ \theta_i }[/math] for the flux density calibrator 3C 286.
# In CASA
gaincal(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.G1',
field='J1331+3030',spw='0:5~58',
solint='inf',refant='ea21',gaintype='G',calmode='ap',solnorm=F,
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0'])
- caltable='3c391_ctm_mosaic_10s_spw0.G1' : Produce a new calibration table containing these gain solutions. In order to make the bookkeeping easier, a '1' is appended to the file name to distinguish it from the earlier set of gain solutions, which are effectively being "thrown away."
- spw='0:5~58' : From the inspection of the bandpass, one can determine the range of edge channels that are affected by the bandpass filter rolloff. Because the amplitude is dropping rapidly in these channels, one does not want to include them in the solution.
- gaintype='G', calmode='ap', solnorm=F : Solve for the complex antenna gains for 3C 286. The objective is to relate the measured data values to the (assumed known) flux density of 3C 286, thus the solution is both amplitude and phase ('ap') and the solutions should not be normalized to unity amplitude.
- solint='inf' : Produce a solution for each scan. Phase coherence for these observations is good.
- gaintable: Use the antenna position corrections, delays, and bandpass solutions determined earlier before solving for the gain amplitudes.
In the second step, the appropriate complex gains for a direction on the sky close to the target source will be determined from the phase calibrator J1822-0938. We also determine the complex gains for the polarization calibrator source J0319+4130. These will be solved separately, but in practice could be solved together as there are no gaintables that are time dependent at this point (and thus would risk having cross-source interpolation issues) nor are we doing different solution intervals per source.
# In CASA
gaincal(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.G1',
field='J1822-0938',
spw='0:5~58',solint='inf',refant='ea21',gaintype='G',calmode='ap',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0'],
append=True)
#
gaincal(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.G1',
field='J0319+4130',
spw='0:5~58',solint='inf',refant='ea21',gaintype='G',calmode='ap',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0'],
append=True)
- caltable='3c391_ctm_mosaic_10s_spw0.G1', append=True: In all previous invocations of gaincal, append has been set to False. Here, the gain solutions from the phase calibrators are going to be appended to the existing set from 3C 286. In following steps, all of these gain solutions will then be used together to derive a set of complex gains that are applied to the science data for the target source.
If one checks the gain phase solutions using plotcal, one should see smooth solutions for each antenna as a function of time.
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G1',xaxis='time',yaxis='phase',
poln='R',plotrange=[-1,-1,-180,180],figfile='plotcal_3c391-G1-phase-R.png')
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G1',xaxis='time',yaxis='phase',
poln='L',plotrange=[-1,-1,-180,180],figfile='plotcal_3c391-G1-phase-L.png')
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G1',xaxis='time',yaxis='amp',
poln='R',figfile='plotcal_3c391-G1-amp-R.png')
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G1',xaxis='time',yaxis='amp',
poln='L',figfile='plotcal_3c391-G1-amp-L.png')
 |
 |
 |
 |
This is also a good time to check that our chosen reference antenna (ea21) has good phase stability (i.e., the phase difference between the right and left polarizations is stable with time). This is a prerequisite for accurate polarization calibration. To do this, we plot the complex polarization ratio:
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.G1', xaxis='time', yaxis='phase',
poln='/', plotrange=[-1,-1,-180,180], figfile='plotcal_3c391-G1-phase-rat.png')
As can be seen in the plot, there is a bit of drift (a few degrees here and there), but no phase jumps. This means that ea21 is, indeed, a good choice for reference antenna.
 |
Polarization Calibration
[If time is running short, skip this step and proceed to [Applying the Calibration].] ("Stay on target." Gold Five)
Having set the complex gains, we now need to do the polarization calibration. This should be done prior to running fluxscale, since it has to run using the un-rescaled gains in the MODEL_DATA column of the measurement set. Polarization calibration is done in two steps. First, we solve for the instrumental polarization (the frequency-dependent leakage terms, or 'D-terms'), using either an unpolarized source or a source which has sufficiently good parallactic angle coverage. Second, we solve for the polarization position angle using a source with a known polarization position angle (3C 286 is recommended here).
Our initial run of setjy only set the total intensity of our flux calibrator source, 3C 286. This source is known to have a fairly stable fractional polarization (measured to be 11.2% in C-band around the time of the observations), and a polarization position angle of 66 degrees (at most frequencies). For information on polarization calibrators suitable for VLA observations, see the VLA Observing Guide to Polarimetry. The most recently determined values (given in a table at the bottom of the Polarimetry guide page) give 11.3% at 4.5GHz, but below we use the old value of 11.2% for consistency with the rest of the guide.
In order to calibrate the position angle, we need to set the appropriate values for Stokes Q and U. Examining our casapy.log file to find the output of setjy, we find that the total intensity was set to 7.81694 Jy in channel 0 of spw 0, at 4536 MHz according to the listobs output. We therefore use python to find the polarized flux, P, and the values of Stokes Q and U at this reference channel:
# In CASA
i0=7.81694 # Stokes I value for spw 0 ch 0
p0=0.112*i0 # Fractional polarization=11.2%
q0=p0*cos(66*pi/180) # Stokes Q for spw 0
u0=p0*sin(66*pi/180) # Stokes U for spw 0
Furthermore, in CASA 3.4, we can introduce a spectral index to the flux densities. We do this by noting that our printout from setjy gave 7.68506 Jy in the last channel 127 (at 4663 MHz). Therefore we use python again to compute a spectral index
# In CASA
alpha = log(7.68506/7.81694)/log(4663.0/4536.0)
which gives alpha = -0.61618.
We now set the values of Stokes I, Q and U for 3C 286, using setjy using these values. First, because we still have the old I-only model in the header, we will delete this:
# In CASA
delmod('3c391_ctm_mosaic_10s_spw0.ms')
NOTE: In CASA 4.0 if you do not do this delmod both the old and new models will be in the header and will be used, doubling the fluxes and confusing other tasks. In future releases we will have the second setjy properly replace the old model.
Now we generate the polarization model:
# In CASA
setjy(vis='3c391_ctm_mosaic_10s_spw0.ms',field='J1331+3030',modimage='',
spw='0',fluxdensity=[i0,q0,u0,0],spix=alpha,reffreq='4536.0MHz',
scalebychan=True,usescratch=False)
- modimage=' ' : A model image is not used here.
- fluxdensity=[i0,q0,u0,0] : use the IQUV values for channel 0 calculated above
- spix=alpha : Set the spectral index using the formula above (this will also apply to QU)
- reffreq='4536.0MHz' : The frequency of channel 0 from listobs
- scalebychan=True : let it compute a value per channel
- usescratch=False : DO NOT create/use the MODEL_DATA column explicitly
Note that the Stokes V flux value is set to zero, corresponding to no circular polarization.
We can see the results in the model column in plotms
# In CASA
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='0',correlation='RR',
timerange='08:02:00~08:17:00',antenna='ea01&ea02',
xaxis='channel',yaxis='amp',ydatacolumn='model',
plotfile='plotms_3c391-model-amp-RR.png')
showing our model source spectrum. We can see this translates to the spectrum in QU
# In CASA
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='0',correlation='RL',
timerange='08:02:00~08:17:00',antenna='ea01&ea02',
xaxis='channel',yaxis='amp',ydatacolumn='model',
plotfile='plotms_3c391-model-amp-RL.png')
Finally, our R-L phase difference is constant at 66 degrees as desired:
# In CASA
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='0',correlation='RL',
timerange='08:02:00~08:17:00',antenna='ea01&ea02',
xaxis='channel',yaxis='phase',ydatacolumn='model',
plotrange=[-1,-1,-180,180],plotfile='plotms_3c391-model-phase-RL.png')
 |
 |
 |
Solving for the Cross-Hand delays
Just as we did for the parallel-hand (RR,LL) delays before bandpass calibration, we solve for the cross-hand (RL,LR) delays due to the residual delay difference between the R and L on the reference antenna (ea21) used for the original delay calibration. In our case we simply use 3C286 which has a strong polarized signal in the RL,LR correlations.
# In CASA
gaincal(vis='3c391_ctm_mosaic_10s_spw0.ms', caltable='3c391_ctm_mosaic_10s_spw0.Kcross',
field='J1331+3030', spw='0:5~58',
gaintype='KCROSS', solint='inf', combine='scan', refant='ea21',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0',
'3c391_ctm_mosaic_10s_spw0.G1'],
gainfield=['','','','J1331+3030'],
interp=['linear','nearest','nearest','linear'], parang=T)
We can plot these:
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.Kcross',xaxis='antenna',yaxis='delay',
figfile='plotcal_3c391-Kcross-delay.png')
As expected there is a single value for R versus L (with L delay set to zero) across all antennas. The solution is reported in the logger, and is 7.149 ns.
Note that if we did not solve for this delay, it would be absorbed into the phases per channel of the following Df and Xf solutions. This would not cause us problems, as we are not solving for the Q+iU polarization of our D-term calibrator (we are using unpolarized 3C84 for that) but if we were (e.g. using our gain calibrator J1822-0938 with poltype='Df+QU') then this step would be essential.
Solving for the Leakage Terms
The task polcal is used for polarization calibration. In this data set, we observed the unpolarized calibrator J0319+4130 (a.k.a. 3C 84) in order to solve for the instrumental polarization. polcal uses the Stokes I, Q, and U values in the MODEL_DATA column (Q and U being zero for our unpolarized calibrator) to derive the leakage solutions. The function call is
# In CASA
polcal(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.D1',
field='J0319+4130',spw='0:5~58',
refant='ea21',poltype='Df',solint='inf',combine='scan',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0',
'3c391_ctm_mosaic_10s_spw0.G1',
'3c391_ctm_mosaic_10s_spw0.Kcross'],
gainfield=['','','','J0319+4130',''],
interp=['linear','nearest','nearest','linear','nearest'])
- caltable='3c391_ctm_mosaic_10s_spw0.D1' : polcal will create a new calibration table containing the leakage solutions, which we specify with the caltable argument.
- field='J0319+4130' : The unpolarized source J0319+4130 (a.k.a. 3C 84) is used to solve for the leakage terms.
- spw='0:5~58' : In this example, the edge channels are not used in finding the solution. Because the bandpass is one of the calibration tables being applied (in gaintable), this restriction is not necessary. However, if one restricts the spectral window here, it must also be restricted in the remainder of the calibration steps, particularly applycal, otherwise the final data set will contain frequency channels for which the leakage terms have not been calibrated.
- poltype='Df' : We will solve for the leakages (D) on a per-channel basis (f) assuming zero source polarization.
- solint='inf' : One solution over the entire run (the default)
- combine='scan' : Combine all scans together (the default)
- gaintable : All of the previous corrections---antenna positions, K-delay, bandpass, Kcross-delay, and complex gain---are to be applied
- gainfield : The gain caltable that is being applied on the fly, 3c391_ctm_mosaic_10s_spw0.G1, contains the solutions for multiple sources. Only the solutions from J0319+4130 should be applied to itself in the process of finding the polarization leakage terms.
- interp : The interpolation to be used for each gaintable.
After polcal has finished running, you are strongly advised to examine the solutions with plotcal, to ensure that everything looks good.
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.D1',xaxis='chan',yaxis='amp',
spw='',field='',iteration='antenna')
#
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.D1',xaxis='chan',yaxis='phase',
spw='',field='',iteration='antenna',plotrange=[-1,-1,-180,180])
This will produce plots similar to those shown at right. As ever, you can cycle through the antennas by clicking the "Next" button. You should see leakages of between 5 and 15% in most cases. We can also display these in a single plot versus antenna index:
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.D1',xaxis='antenna',yaxis='amp',
figfile='plotcal_3c391-D1.png')
Note that there are no solutions for antenna ea04 - a bit of sleuthing will turn up that ea04 was missing for the scans on 3C84.
If we want to rescue ea04 (which otherwise seems ok) then we turn to our gain calibrator. If we plot data for field 1 versus ParAngle in plotms then we see that it has sufficient range (>60 deg) in parallactic angle so should be useable as a calibrator with unknown polarization. We can make a new set of solutions:
# In CASA
polcal(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.D2',
field='J1822-0938',spw='0:5~58',
refant='ea21',poltype='Df+QU',solint='inf',combine='scan',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0',
'3c391_ctm_mosaic_10s_spw0.G1',
'3c391_ctm_mosaic_10s_spw0.Kcross'],
gainfield=['','','','J1822-0938',''],
interp=['linear','nearest','nearest','linear','nearest'])
- field='J1822-0938' : Our gain calibrator observed throughout the schedule block
- poltype='Df+QU' : Solve for the leakages using a calibrator with unknown polarization but with good parallactic angle coverage, and simultaneously for the source polarization (averaged over frequency)
- gainfield : For 3c391_ctm_mosaic_10s_spw0.G1 use only the solutions from J1822-0938 itself.
We now plot this as we did before:
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.D2',xaxis='antenna',yaxis='amp',
figfile='plotcal_3c391-D2.png')
Comparison of this plot with that for the D1 caltable shows that we get nearly identical results, but now ea04 (index 3) is present! That should give us some confidence in our leakage calibration as well.
Solving for the R-L polarization angle
Having calibrated the instrumental polarization, the total polarization is now correct, but the R-L phase still needs to calibrated in order to obtain an accurate polarization position angle. We use the same task, polcal, but this time set poltype='Xf, which specifies a frequency-dependent (f) position angle (X) calibration, using the source J1331+3030 (a.k.a. 3C 286), whose position angle is known, having set this earlier using setjy. Note that we must correct for the leakages before determining the R-L phase, which we do by adding the calibration table made in the previous step (3c391_ctm_mosaic_10s_spw0.D2) to the gain tables that are applied on-the-fly. Note that we are using the second D table we made as it included ea04.
# In CASA
polcal(vis='3c391_ctm_mosaic_10s_spw0.ms',caltable='3c391_ctm_mosaic_10s_spw0.X1',
field='J1331+3030',combine='scan',
poltype='Xf',solint='inf',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0',
'3c391_ctm_mosaic_10s_spw0.G1',
'3c391_ctm_mosaic_10s_spw0.Kcross',
'3c391_ctm_mosaic_10s_spw0.D2'],
gainfield=['','','','J1331+3030','',''],
interp=['linear','nearest','nearest','linear','nearest','nearest'])
Again, it is strongly suggested that you check the calibration worked properly, by plotting up the newly-generated calibration table using plotcal. The results are shown at right.
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.X1',xaxis='chan',yaxis='phase',
figfile='plotcal_3c391-X1.png')
Because the Xf term captures the residual R-L phase on the reference antenna over the array, there is one value for all antennas. Also, as we took out the RL delays using the Kcross solution, these Xf variations only span about 6 degress across the spectral window.
At this point, you have all the necessary polarization calibration tables.
Scaling the Amplitude Gains
While we know the flux density of our primary calibrator (in our case, J1331+3030[math]\displaystyle{ \equiv }[/math]3C 286), the model assumed for the secondary calibrator (here, J1822-0938) was a point source of 1 Jy located at the phase center. While the secondary calibrator was chosen to be a point source (at least, over some limited range of uv-distance; see the VLA calibrator manual for any u-v restrictions on your calibrator of choice at the observing frequency), its absolute flux density is unknown. Being pointlike, secondary calibrators typically vary on timescales of months to years, in some cases by up to 50--100%. A nice Java Applet is available to track the flux density history of various calibrators over time. Play around with it to see how much some of the calibrators from the manual can vary, and over what sorts of timescales.
We use the primary calibrator (the 'flux calibrator') to determine the system response to a source of known flux density, and assume that the mean gain amplitudes for the primary calibrator are the same as those for the secondary calibrator. This then allows us to find the true flux density of the secondary calibrator. To do this, we use the task fluxscale, which produces a new calibration table containing properly-scaled amplitude gains for the secondary calibrator.
# In CASA
myscale = fluxscale(vis='3c391_ctm_mosaic_10s_spw0.ms',
caltable='3c391_ctm_mosaic_10s_spw0.G1',
fluxtable='3c391_ctm_mosaic_10s_spw0.fluxscale1',
reference=['J1331+3030'],
transfer=['J1822-0938,J0319+4130'])
- myscale = fluxscale() : fluxscale returns a dictionary of results, which we capture in the variable myscale
- caltable='3c391_ctm_mosaic_10s_spw0.G1' : We provide fluxscale with the calibration table containing the amplitude gain solutions derived earlier.
- fluxtable='3c391_ctm_mosaic_10s_spw0.fluxscale1' : We specify the name of the new output table to be written, which will contain the properly-scaled amplitude gains.
- reference='J1331+3030' : We specify the source with the known flux density.
- transfer=['J1822-0938,J0319+4130'] : We specify the sources whose amplitude gains are to be rescaled.
fluxscale will print to the CASA logger the derived flux densities of all calibrator sources specified with the transfer argument. These are also captured in the return variable from the task. You should examine the output to ensure that it looks sensible. If one's data set has more than 1 spectral window, depending upon where they are spaced and the spectrum of the source, it is quite possible to find (quite) different flux densities and spectral indexes for the secondary calibrators. Example output would be
CASA <314>: myscale['1']
Out[314]:
{'fieldName': 'J1822-0938',
'fluxd': array([ 2.34086514]),
'fluxdErr': array([ 0.00638615]),
'numSol': array([46], dtype=int32),
'spidx': array([ 0., 0., 0.]),
'spidxerr': array([ 0., 0., 0.])}
CASA <315>: myscale['9']
Out[315]:
{'fieldName': 'J0319+4130',
'fluxd': array([ 13.93359175]),
'fluxdErr': array([ 0.03865693]),
'numSol': array([44], dtype=int32),
'spidx': array([ 0., 0., 0.]),
'spidxerr': array([ 0., 0., 0.])}
or in the logger
##########################################
##### Begin Task: fluxscale #####
fluxscale(vis="3c391_ctm_mosaic_10s_spw0.ms",caltable="3c391_ctm_mosaic_10s_spw0.G1",fluxtable="3c391_ctm_mosaic_10s_spw0.fluxscale1",reference=['J1331+3030'],
transfer=['J1822-0938,J0319+4130'],listfile="",append=False,refspwmap=[-1],incremental=False,
fitorder=1)
Opening MS: 3c391_ctm_mosaic_10s_spw0.ms for calibration.
Initializing nominal selection to the whole MS.
Beginning fluxscale--(MSSelection version)-------
Found reference field(s): J1331+3030
Found transfer field(s): J1822-0938 J0319+4130
Flux density for J1822-0938 in SpW=0 is: 2.34086 +/- 0.00638755 (SNR = 366.473, N = 46)
Flux density for J0319+4130 in SpW=0 is: 13.9336 +/- 0.0386569 (SNR = 360.442, N = 44)
Storing result in 3c391_ctm_mosaic_10s_spw0.fluxscale1
Writing solutions to table: 3c391_ctm_mosaic_10s_spw0.fluxscale1
##### End Task: fluxscale #####
##########################################
The VLA calibrator manual can be used to check whether the derived flux densities look sensible. Wildly different flux densities or flux densities with very high error bars should be treated with suspicion; in such cases you will have to figure out whether something has gone wrong.
We plot the rescaled amplitudes from this table:
# In CASA
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.fluxscale1',xaxis='time',yaxis='amp',
poln='R',figfile='plotcal_3c391-fluxscale1-amp-R.png')
plotcal(caltable='3c391_ctm_mosaic_10s_spw0.fluxscale1',xaxis='time',yaxis='amp',
poln='L',figfile='plotcal_3c391-fluxscale1-amp-L.png')
You can see (in the plots shown below) that the amplitude gain factors are now similar across sources, compared to the raw factors in the G1 table.
 |
 |
Applying the Calibration
Now that we have derived all the calibration solutions, we need to apply them to the actual data, using the task applycal. The measurement set DATA column contains the original data. To apply the calibration we have so painstakingly derived, we specify the appropriate calibration tables, which are then applied to the DATA column, with the results being written in the CORRECTED_DATA column. If the dataset does not already have a CORRECTED_DATA scratch column, then one will be created in the first applycal run.
First, we apply the calibration to each individual calibrator, using the gain solutions derived on that calibrator alone to compute the CORRECTED_DATA. To do this, we iterate over the different calibrators, in each case specifying the source to be calibrated (using the field parameter). The relevant function calls are given below, although as explained presently, the calls to applycal will differ slightly if you skipped the [Polarization Calibration].
# In CASA
applycal(vis='3c391_ctm_mosaic_10s_spw0.ms',
field='J1331+3030',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.fluxscale1',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0',
'3c391_ctm_mosaic_10s_spw0.Kcross',
'3c391_ctm_mosaic_10s_spw0.D2',
'3c391_ctm_mosaic_10s_spw0.X1'],
gainfield=['','J1331+3030','','','','',''],
interp=['','nearest','','','','',''],
parang=True,calwt=F)
#
applycal(vis='3c391_ctm_mosaic_10s_spw0.ms',
field='J0319+4130',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.fluxscale1',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0',
'3c391_ctm_mosaic_10s_spw0.Kcross',
'3c391_ctm_mosaic_10s_spw0.D2',
'3c391_ctm_mosaic_10s_spw0.X1'],
gainfield=['','J0319+4130','','','','',''],
interp=['','nearest','','','','',''],
parang=True,calwt=F)
#
applycal(vis='3c391_ctm_mosaic_10s_spw0.ms',
field='J1822-0938',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.fluxscale1',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0',
'3c391_ctm_mosaic_10s_spw0.Kcross',
'3c391_ctm_mosaic_10s_spw0.D2',
'3c391_ctm_mosaic_10s_spw0.X1'],
gainfield=['','J1822-0938','','','','',''],
interp=['','nearest','','','','',''],
parang=True,calwt=F)
- gaintable : We provide a Python list of the calibration tables to be applied. This list must contain the antenna position corrections (in .antpos), the properly-scaled gain calibration for the amplitudes and phases (in .fluxscale1) which were just made using fluxscale, the parallel-hand delays (in .K0), the bandpass solutions (in .B0), the cross-hand delays (in .Kcross), the leakage calibration (in .D2 derived by our second solution), and the R-L phase corrections (in .X1).
- gainfield, interp : To ensure that we use the correct gain amplitudes and phases for a given calibrator (those derived on that same calibrator), then for each calibrator source, we need to specify the particular subset of gain solutions to be applied. This requires use of the gainfield and interp arguments; these are both Python lists, and for the list item corresponding to the calibration table made by fluxscale, we set gainfield to the field name corresponding to that calibrator, and the desired interpolation type (interp) to nearest.
- parang : Since we have performed polarization calibration, we must set parang=True, or we will discard all that hard work we did earlier. However, if you skipped the [Polarization_Calibration] section, the .Kcross, .D2 and .X1 will not exist. In this case, you should leave out these tables from the gaintable list, and the corresponding sets of elements in the gainfield list each time you run applycal above. You should also set parang=False.
- calwt=F : At the time of writing, we are not yet using system calibration data to compute real (1/Jy2) weights, thus trying to calibrate them can produce nonsensical results. In particular, experience has shown that calibrating the weights will lead to problems especially in the self-calibration steps.
Finally, we apply the calibration to the target fields in the mosaic, linearly interpolating the gain solutions from the secondary calibrator, J1822-0938. In this case however, we want to apply the amplitude and phase gains derived from the secondary calibrator, J1822-0938, since that is close to the target source on the sky, and we assume that the gains applicable to the target source are very similar to those derived in the direction of the secondary calibrator. Of course, this is not strictly true, since the gains on J1822-0938 were derived at a different time and in a different position on the sky from the target. However, assuming that the calibrator was sufficiently close to the target, and the weather was sufficiently well-behaved, then this is a reasonable approximation, and should get us a sufficiently good calibration that we can later use self-calibration to correct for the small inaccuracies thus introduced.
The procedure for applying the calibration to the target source is very similar to what we just did for the calibrator sources.
# In CASA
applycal(vis='3c391_ctm_mosaic_10s_spw0.ms',
field='2~8',
gaintable=['3c391_ctm_mosaic_10s_spw0.antpos',
'3c391_ctm_mosaic_10s_spw0.fluxscale1',
'3c391_ctm_mosaic_10s_spw0.K0',
'3c391_ctm_mosaic_10s_spw0.B0',
'3c391_ctm_mosaic_10s_spw0.Kcross',
'3c391_ctm_mosaic_10s_spw0.D2',
'3c391_ctm_mosaic_10s_spw0.X1'],
gainfield=['','J1822-0938','','','','',''],
interp=['','linear','','','','',''],
parang=True,calwt=F)
- field : We can calibrate all seven target fields at once by setting field='2~8' .
- gainfield : In this case, we wish to use the gains derived on the secondary calibrator, for the reasons explained in the previous paragraph.
- interp : This time, we linearly interpolate between adjacent calibrator scans, to compute the appropriate gains for the intervening observations of the target.
 |
 |
 |
 |
We should now have fully-calibrated visibilities in the CORRECTED_DATA column of the measurement set, and it is worthwhile pausing to inspect them, to ensure that the calibration did what we expected it to. We make some standard plots (see above):
# In CASA
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='0',correlation='',
timerange='08:02:00~08:17:00',antenna='',avgtime='60s',
xaxis='channel',yaxis='amp',ydatacolumn='corrected',
plotfile='plotms_3c391-fld0-corrected-amp.png')
#
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='0',correlation='',
timerange='08:02:00~08:17:00',antenna='',avgtime='60s',
xaxis='channel',yaxis='phase',ydatacolumn='corrected',
plotrange=[-1,-1,-180,180],coloraxis='corr',
plotfile='plotms_3c391-fld0-corrected-phase.png')
#
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='1',correlation='RR,LL',
timerange='',antenna='',avgtime='60s',
xaxis='channel',yaxis='amp',ydatacolumn='corrected',
plotfile='plotms_3c391-fld1-corrected-amp.png')
#
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='1',correlation='RR,LL',
timerange='',antenna='',avgtime='60s',
xaxis='channel',yaxis='phase',ydatacolumn='corrected',
plotrange=[-1,-1,-180,180],coloraxis='corr',
plotfile='plotms_3c391-fld1-corrected-phase.png')
For 3C286 (leftmost plots) we see the polarized signal in the cross-hands. There is no sign of bad data remaining.
Another nice display is to use plotms to plot the amplitude and phase of the CORRECTED_DATA column against one another, for one of the parallel-hand correlations (RR or LL; the signal in the cross-hands, RL and LR is much smaller, and will be noiselike for an unpolarized calibrator). This should then show a nice ball of visibilities centered at zero phase (with some scatter) and the amplitude found for that source in fluxscale. An example is shown at right.
# In CASA
plotms(vis='3c391_ctm_mosaic_10s_spw0.ms',field='1',correlation='RR,LL',
timerange='',antenna='',avgtime='60s',
xaxis='phase',xdatacolumn='corrected',yaxis='amp',ydatacolumn='corrected',
plotrange=[-180,180,0,3],coloraxis='corr',
plotfile='plotms_3c391-fld1-corrected-ampvsphase.png')
Inspecting the data at this stage may well show up previously-unnoticed bad data. Plotting up the corrected amplitude against UV distance, or against time is a good way to find such issues. If you find bad data, you can remove them via interactive flagging in plotms, or via manual flagging in flagdata once you have identified the offending antennas/baselines/channels/times. When you are happy that all data (particularly on your target source) look good, you may proceed.
Now that the calibration has been applied to the target data, we can split off the science targets, creating a new, calibrated measurement set containing all the target fields.
# In CASA
split(vis='3c391_ctm_mosaic_10s_spw0.ms',outputvis='3c391_ctm_mosaic_spw0.ms',
datacolumn='corrected',field='2~8')
- outputvis : We give the name of the new measurement set to be written, which will contain the calibrated data on the science targets.
- datacolumn : We use the CORRECTED_DATA column, containing the calibrated data which we just wrote using applycal.
- field : We wish to put all the mosaic pointings into a single measurement set, for imaging and joint deconvolution.
Initial Imaging
Now that we have split off the target data into a separate measurement set with all the calibration applied, it's time to make an image. Recall from the lectures that the visibility data and the sky brightness distribution (a.k.a. image) are Fourier transform pairs
[math]\displaystyle{ I(l,m) = \int V(u,v) e^{[2\pi i(ul + vm)]} dudv }[/math]
The [math]\displaystyle{ u }[/math] and [math]\displaystyle{ v }[/math] coordinates are the baselines, measured in units of the observing wavelength while the [math]\displaystyle{ l }[/math] and [math]\displaystyle{ m }[/math] coordinates are the direction cosines on the sky. For generality, the sky coordinates are written in terms of direction cosines, but for most EVLA (and ALMA) observations they can be related simply to the right ascension ([math]\displaystyle{ l }[/math]) and declination ([math]\displaystyle{ m }[/math]). Also recall from the lectures that this equation is valid only if the [math]\displaystyle{ w }[/math] coordinate of the baselines can be neglected. This assumption is almost always true at high frequencies and smaller EVLA configurations (such as the 4.6 GHz, D-configuration observations here); the [math]\displaystyle{ w }[/math] coordinate cannot be neglected at lower frequencies and larger configurations (e.g., 0.33 GHz, A-configuration observations). This expression also neglects other factors, such as the shape of the primary beam. For more information on imaging, see [Synthesis Imaging] within the CASA Reference Manual.
CASA has a single task, clean which both Fourier transforms the data and deconvolves the resulting image. For the purposes of this tutorial Part 1, we will make a simple mosaic clean image in Stokes I only. In Part 2 we will proceed to make multiscale mosaic images in IQUV and to analyze them.
Setting the appropriate pixel size for imaging depends upon basic optics aspects of interferometry. Using plotms to look at the newly-calibrated, target-only data set,
# In CASA
plotms(vis='3c391_ctm_mosaic_spw0.ms',xaxis='uvwave',yaxis='amp',
ydatacolumn='data', field='0',avgtime='30s',correlation='RR',
plotfile='plotms_3c391-mosaic0-uvwave.png',overwrite=True)
one should obtain a plot similar to the one shown at the right with the (calibrated) visibility amplitude as a function of [math]\displaystyle{ u }[/math]-[math]\displaystyle{ v }[/math] distance. The maximum baseline is about 16,000 wavelengths, i.e., an angular scale of 12 arcseconds ([math]\displaystyle{ \lambda/D=1/16000 }[/math]). The most effective CLEANing occurs with 3--5 pixels across the synthesized beam. For example, a cell size of 2.5 arcseconds will give just under 5 pixels per beam.
The supernova remnant itself is known to have a diameter of order 9 arcminutes, corresponding to about 216 pixels for the chosen cell size. The mosaic was set up with 7 fields, 1 centered on the remnant and 6 flanking fields; the spacing of the fields was chosen based on the size of the (antenna) primary beam. For the choice of ftmachine='mosaic' (our main mosaicing algorithm), you do not have to fit the mosaic inside the inner quarter of the total image in order to prevent image artifacts arising from aliasing, we just want to have a bit of padding around the outside. Although CASA has the feature that its Fourier transform engine (FFTW) does not require a strict power of 2 for the number of linear pixels in a given image axis, it is somewhat more efficient if the number of pixels on a side is a composite number divisible by any pair of 2 and 3 and/or 5. Because clean internally applies a padding of 1.2 (=3x2/5) choose 480, which is 25 x 3 x 5 (so 480 x 1.2 = 576 = 26 x 32). We therefore set imsize=[480,480] and our mosaic fits comfortably inside the image.
To make this simple clean image interactively:
# In CASA
clean(vis='3c391_ctm_mosaic_spw0.ms',
imagename='3c391_ctm_spw0_noms_I',
field='',spw='',
mode='mfs',
niter=5000,
gain=0.1, threshold='1.0mJy',
psfmode='clark',
imagermode='mosaic', ftmachine='mosaic',
multiscale=[0],
interactive=True,
imsize=[480,480], cell=['2.5arcsec','2.5arcsec'],
stokes='I',
weighting='briggs',robust=0.5,
usescratch=False)
clean is a powerful task, with many inputs, and a certain amount of experimentation may be (likely is) required.
- vis='3c391_ctm_mosaic_spw0.ms' : this split MS contains our 7-pt mosaic fields, now indexed as 0-6. Field 0 is the central field of the mosaic (you can use listobs to verify this).
- imagename='3c391_ctm_spw0_noms_I' : our output images will all start with this, e.g. 3c391_ctm_spw0_noms_I.image
- mode='mfs' : Use multi-frequency synthesis imaging. The fractional bandwidth of these data is non-zero (128 MHz at a central frequency of 4.6 GHz). Recall that the [math]\displaystyle{ u }[/math] and [math]\displaystyle{ v }[/math] coordinates are defined as the baseline coordinates, measured in wavelengths. Thus, slight changes in the frequency from channel to channel result in slight changes in [math]\displaystyle{ u }[/math] and [math]\displaystyle{ v }[/math]. There is a concomitant improvement in [math]\displaystyle{ u }[/math]-[math]\displaystyle{ v }[/math] coverage if the visibility data from the multiple spectral channels are gridded separately onto the [math]\displaystyle{ u }[/math]-[math]\displaystyle{ v }[/math] plane, as opposed to treating all spectral channels as having the same frequency.
- niter=25000,gain=0.1,threshold='1.0mJy' : Recall that the CLEAN gain is the amount by which a CLEAN component is subtracted during the CLEANing process. niter and threshold are (coupled) means of determining when to stop the CLEANing process, with niter specifying to find and subtract that many CLEAN components while threshold specifies a minimum flux density threshold a CLEAN component can have before CLEAN stops. See also interactive below. Imaging is an iterative process, and to set the threshold and number of iterations, it is usually wise to CLEAN interactively in the first instance, stopping when spurious emission from sidelobes (arising from gain errors) dominates the residual emission in the field. Here, we have used our experience in interactive mode to set a threshold level based on the rms noise in the resulting image. The number of iterations should then be set high enough to reach this threshold.
- interactive=True : Very often, particularly when one is exploring how a source appears for the first time, it can be valuable to interact with the CLEANing process. If True, interactive causes a viewer window to appear. One can then set CLEAN regions, restricting where CLEAN searches for CLEAN components, as well as monitor the CLEANing process. A standard procedure is to set a large value for niter, and stop the CLEANing when it visually appears to be approaching the noise level. This procedure also allows one to change the CLEANing region, in cases when low-level intensity becomes visible as the CLEANing process proceeds.
- imsize=[480,480],cell=['2.5arcsec'] : See the discussion above regarding the setting of the image size and cell size. If only one value is specified, the same value is used in both directions.
- stokes='I',psfmode='clark' : A single image will be made for total intensity I.
- weighting='briggs',robust=0.5 : 3C 391 has diffuse, extended emission that is (at least partially) resolved out by the interferometer owing to a lack of short spacings. A naturally-weighted image would show large-scale patchiness in the noise. In order to suppress this effect, Briggs weighting is used (intermediate between natural and uniform weighting), with a default robust factor of 0.5 (which corresponds to something between natural and uniform weighting).
- imagermode='mosaic', ftmachine='mosaic' : The data consist of a 7-pointing mosaic, since the supernova remnant fills almost the full primary beam at 4.6 GHz. A mosaic combines the data from all of the fields, with imaging and deconvolution being done jointly on all 7 fields. A mosaic both helps compensate for the shape of the primary beam and reduces the amount of large (angular) scale structure that is resolved out by the interferometer.
- multiscale=[0] : For now, we will clean with a single scale of size 0 (a classic clean delta-function)
- usescratch=False As in calibration, we will NOT require use of a physical MODEL_DATA scratch column.
As mentioned above, we can guide the clean process by allowing it to find clean components only within a user-specified region. The easiest way to do this is via interactive clean. When clean runs in interactive mode, a viewer window will pop up as shown right. To get a more detailed view of the central regions containing the emission, zoom in by tracing out a rectangle with the left mouse button and double-clicking inside the zoom box you just made. Play with the color scale to bring out the emission better, by holding down the middle mouse button and moving it around. To create a clean box (a region within which components may be found), hold down the right mouse button and trace out a rectangle around the source, then double click inside that rectangle to set it as a box. Note that the CLEAN box must turn white for it to be registered; if the box is not white, it has not been set! Alternatively, you can trace out a more generic shape to better enclose the irregular outline of the supernova remnant. To do that, right-click on the closed polygonal icon. Then trace out a shape by right-clicking where you want the corners of that shape. Once you have come full circle, the shape will be traced out in green, with small squares at the corners. Double-click inside this region and the green outline will turn white. You have now set the clean region. If you have made a mistake with your clean box, click on the "Erase" button, trace out a rectangle around your erroneous region, and double click inside that rectangle. You can also set multiple clean regions. By default, all clean regions will apply only to the plane shown. To change this to select all planes, click the "All Channels" button at the top (we have only a single mfs channel in the image cube), and likewise for Stokes planes using the "All Polarizations" (you will need to set this when we image all the Stokes).
At any stage in the cleaning, you can adjust the number of iterations that clean will do before returning to the GUI. By default this is set to 100 (see the "iterations" window in mid-upper left of panel). You probably want to set this to a high number for this mosaic due to the complicated structure, values from 1000 to 5000 later on seem to work. Note that this will override the niter that was set when you started the clean task. Clean will keep going until it reaches threshold or runs out of cycles (the "cycles" window to the right of the "iterations").
When you are happy with the clean regions, press the green circular arrow button on the far right to continue deconvolution. After completing a cycle, a revised image will come up. As the brightest points are removed from the image ("cleaned" off), fainter emission may show up. You can adjust the clean boxes each cycle, to enclose all real emission. After many cycles, once only noise is left, you can hit the red and white cross icon to stop cleaning. The second figure to the right shows the interactive clean panel late in the process (after cleaning around 10000 iterations). At this point we have used the polygon tool to draw around the emission. There is still signal left in the residual, and it would take forever to clean all that out using our standard clean! You should just quit after doing around 10000-20000 iterations total. We'll improve this in the next part of the tutorial.
clean will make several output files, all named with the prefix given as imagename. These include:
- .image - final restored image, with the clean components convolved with a restoring beam and added to the remaining residuals at the end of the imaging process
- .flux - effective response of the telescope (the primary beam)
- .flux.pbcoverage - effective response of the full mosaic image
- .mask - areas where clean has been allowed to search for emission
- .model - sum of all the clean components, which also has been stored as the MODEL_DATA column in the measurement set
- .psf - dirty beam, which is being deconvolved from the true sky brightness during the clean process
- .residual - what is left at the end of the deconvolution process; this is useful to diagnose whether or not to clean more deeply
After the imaging and deconvolution process has finished, you can use the viewer to look at your image.
# In CASA
viewer('3c391_ctm_spw0_noms_I.image')
This will bring up a viewer window containing the image, which should look similar to that shown at right. You can adjust the color scale and zoom in to a selected region by assigning mouse buttons to the icons immediately above the image (hover over the icons to get a description of what they do).
Note that the image is cut off in a circular fashion at the edges, corresponding to the default minimum primary beam response (minpb)within clean of 0.2.
As we saw during the interactive cleaning, this single-scale delta-function cleaning is having problems cleaning out the large-scale emission. You can see the large "clean bowl" of negative emission surrounding the object, and the heavy pixelization of the emission at low levels. We'll try to improve on this in the next part of the tutorial.
Next Steps
In Part 2 of the tutorial we will carry out the polarization imaging, self-calibration, and polarization analysis and display of the data. Continue with 3C391 Tutorial Part 2: Image Analysis, Polarization, Self-calibration
Last checked on CASA Version 4.2.0.
