Antennae Band7 - Imaging for CASA 3.3

Overview

This section of the AntennaeBand7 CASA Guide covers the imaging of the continuum and spectral line data. It begins where the Antennae Band7 - Calibration section left off. If you completed the Calibration section of the guide, then you may want to continue with the calibrated data sets. If you did not complete the Calibration section, then you can download the calibrated uv-data from the region closest to your location:

North America   Europe   East Asia

Then download the file 'Antennae_Band7_CalibratedData.tgz' to obtain the calibrated uvdata. Once the download has finished, unpack the file using 'tar -xvzf Antennae_Band7_CalibratedData.tgz' and change directory (cd) to Antennae_Band7_CalibratedData. You should have Antennae_South.cal.ms and Antennae_North.cal.ms in your working directory. Then start CASA with the 'casapy' command. Be sure you are using version r15777 or later.

Imaging Mosaics

Mosaics like other kinds of images are created in the CASA task clean. To invoke mosaic mode, you simply set the parameter imagermode='mosaic'. The default subparameter ftmachine='mosaic' is then automatically set. This is a joint deconvolution algorithm that works in the uv-plane. A convolution of the primary beam patterns for each pointing in the mosiac is created: the primary beam response function. The corresponding image of the mosaic response function will be called <imagename>.pbcoverage and <imagename>.flux (where the latter differs from the former only if the sensitivity of each field in the mosaic varies).

Well-sampled mosaics like the patterns observed for the Northern and Southern Antennae mosaics shown on the Overview page are well-suited to joint deconvolution. However, if you have a poorly-sampled, or very irregular mosaic you may need to use the slower ftmachine='ft' which combines data in the image plane, similar to what is done in other packages like miriad.

Additionally, for mosaics it is essential to pick the center of the region to be imaged explicitly using the phasecenter parameter. Otherwise it will default to the first pointing included in the field parameter -- since this is often at one corner of the mosaic, the image will not be centered. For the Northern mosaic, the center pointing corresponds to field id=12. Note that during the final split in the calibration section that selected only the Antennae fields, the field ids were renumbered, so that the original centers (shown in the Overview) have changed: field id 14 becomes 12 for the Northern mosaic and field 18 becomes 15 for the Southern mosiac. You can also set an explicit coordinate (see the clean help for syntax).

Continuum Imaging

Fig. 2. Northern mosaic: Amplitude vs. channel. The CO(3-2) line is seen from 70 to 100

Fig. 1. Southern mosaic: Amplitude vs. channel. The CO(3-2) line is seen from 50 to 100

We will make 345 GHz continuum images for the two regions covered by the mosaics. We use the task clean over the channels that are free of the line emission; we avoid the edge channels which tend to be noisier due to bandpass rolloff effects. The line-free channels are found by plotting the average spectrum (all fields). We find the CO(3-2) line from channels 50 to 100 in the southern mosaic, and from 70 to 100 in the northern mosaic.

# In CASA
plotms(vis='Antennae_North.cal.ms',xaxis='channel',yaxis='amp',
      avgtime='1e8',avgscan=T,plotfile='Antennae_North-AMPvsCH.png')

# In CASA
plotms(vis='Antennae_South.cal.ms',xaxis='channel',yaxis='amp',
      avgtime='1e8',avgscan=T,plotfile='Antennae_South-AMPvsCH.png')

The avgtime is set to a large value so that it averages over all the integrations, and avgscan is set to allow averaging of the different scans.

Next we create continuum images from the line-free channels.

Northern Continuum Mosaic

For illustrative purposes we first make a dirty image to see if there is emission and what the exact beam size is. It should be on the order of 1" but this will vary a bit according to the uv-coverage in the actual data. We will start with a cell size of 0.2" to oversample the beam by a factor of 5. The imsize needs to be large enough given the cell size to comfortably encompass the mosaic. From the mosaic footprints shown in the overview, we can see that the Northern mosaic imsize needs to be about 1 arcmin. With 0.2" pixels, this requires a imsize=300.

Other essential clean parameters for this case include:

• vis='Antennae_North.cal.ms': The calibrated dataset on the science target. clean will always use the CORRECTED DATA column (if it exists).
• imagename='Antennae_North.Cont.Clean': The base name of the output images:
  • <imagename>.image # the final restored image
  • <imagename>.flux # the effective primary beam response (e.g. for pbcor)
  • <imagename>.flux.pbcoverage # the primary beam coverage (ftmachine=’mosaic’ only)
  • <imagename>.model # the model image
  • <imagename>.residual # the residual image
  • <imagename>.psf # the synthesized (dirty) beam
• spw='0:1~50;120~164': To specify only the line-free channels of spectral window 0.
• mode='mfs': Multi-Frequency Synthesis: The default mode, which produces one image from all the specified data combined. This will grid each channel independently before imaging. For wide bandwidths this will give a far superior result compared to averaging the channels and then imaging.
• niter=0: Maximum number of clean iterations -- niter=0 will do no cleaning

# In CASA
os.system('rm -rf Antennae_North.Cont.Dirty*')
clean(vis='Antennae_North.cal.ms',imagename='Antennae_North.Cont.Dirty',
     field='',phasecenter='12',
     mode='mfs',restfreq='345.79599GHz',
     spw='0:1~50;120~164',
     imagermode='mosaic',
     imsize=300,cell='0.2arcsec',
     interactive=F,niter=0)

The reported beam size is 1.26" x 0.66" P.A. 86.045 degrees.

# In CASA
viewer('Antennae_North.Cont.Dirty.image')

Fig. 3a. Residual for Northern continuum mosaic after 50 iterations; the clean mask is shown by the white contour.

Yes there is definitely a detection in the vicinity of the Northern nucleus (see Fig. 4 below). Using the square region icon, and drawing a box near but not including the emission, we find the rms noise is about 0.4 mJy/beam in the dirty image.

Next we switch to refined values of cell=0.13" and imsize=500 based on the observed beam size. We also switch to interactive mode so that you can create a clean mask using the polygon tool (note you need to double click inside the polygon region to activate the mask. See here for a more complete description of interactive clean and mask creation.

• niter=1000: Maximum number of clean iterations -- we will stop interactively
• threshold='0.4mJy': Stop cleaning if the maximum residual is below this value (the dirty rms noise)
• interactive=T: Clean will be periodically interupted to show the residual clean image. Interactive clean mask can be made. If no mask is created, no cleaning is done.
• npercycle=50: How many iterations to clean before returning to interactive clean window.

# In CASA
os.system('rm -rf Antennae_North.Cont.Clean*')
clean(vis='Antennae_North.cal.ms',imagename='Antennae_North.Cont.Clean',
     field='',phasecenter='12',
     mode='mfs',restfreq='345.79599GHz',
     spw='0:1~50;120~164',
     imagermode='mosaic',
     imsize=500,cell='0.13arcsec',
     interactive=T,npercycle=50,
     niter=1000, threshold='0.4mJy')

The residuals are "noise-like" after only 50 iterations so hit the red X symbol in the interactive window to stop cleaning here.

Note that if you run the clean task again with the same imagename, without deleting the existing <imagename>.* files, clean assumes that you want to continue cleaning the existing images. We put an rm command before the clean command to guard against this, but sometimes this is what you want.

Southern Continuum Mosaic

Fig. 3b. Residual for Southern continuum mosaic after 50 iterations; the clean mask is shown by the white contour.

For the southern mosaic we modify the phasecenter, mosaic imsize, and the line-free channels (spw)to be consistent for this mosaic. We also bypass the dirty image step we did above for the Northern mosaic. As above, the mosaic size can be judged from here. We expect the beam to be about the same and use the same cell size. During clean, we repeat the process of making a clean mask.

# In CASA
os.system('rm -rf Antennae_South.Cont.Clean*')
clean(vis='Antennae_South.cal.ms',imagename='Antennae_South.Cont.Clean',
     field='',phasecenter='15',
     mode='mfs',restfreq='345.79599GHz',
     spw='0:1~30;120~164',
     imagermode='mosaic',
     imsize=750,cell='0.13arcsec',
     interactive=T,npercycle=50,
     niter=1000, threshold='0.4mJy')

The beam size reported in the logger for the Southern mosaic: 1.15"x 0.66", and P.A.=68 deg; which is a little better than the for the North due to better uv-coverage.

Stop after 50 iterations.

Image Statistics

Fig. 4. Example polygon for rms determination using the viewer.

Fig. 5. 345 GHz continuum image of the northern mosaic made with imview.

Fig. 6. 345 GHz continuum image of the southern mosaic made with imview.

You can determine statistics for the images using the task imstat:

# In CASA
imstat('Antennae_North.Cont.Clean.image')
imstat('Antennae_South.Cont.Clean.image')

From this we find, that for the Northern continuum image the peak is 3.25 mJy/beam and the rms is 0.42 mJy/beam. For the Southern continuum we find a peak of 5.19 mJy/beam and an rms of 0.39 mJy/beam.

However, the calculation of the rms comes with a couple of caveats. First, the mosaic primary beam response rolls off toward the edges of the mosaic, as do correspondingly the flux density and rms. Thus if you don't restrict the measurement to areas of full sensitivity, the apparent rms is skewed downward. Second, since there is real emission in the image, the rms will be skewed upward (with the error increasing with brighter emission). Both can be solved by picking boxes that exclude the edges of the mosaic and the real emission.

It is often easier to use either the viewer directly or imview (a task wrapper for the viewer; see help imview for more info) to display the image and then interactively use the region tools to get the statistics.

# In CASA
viewer('Antennae_North.Cont.Clean.image')

Adjust colorscale using the middle mouse button (or reassign to a different mouse button by clicking on "plus" symbol icon). Next, select the polygon tool by clicking on its symbol with a mouse button. Then draw a region that avoids edges and emission (see example), then double click inside the polygon to have the statistic printed to the screen. We find rms=0.49 mJy/beam. So not much different for this case of weak emission.

# In CASA
viewer('Antennae_South.Cont.Clean.image')

We find rms=0.45 mJy/beam, 13% larger than imstat with no constraints.

Next make hardcopy plots of the continuum images using imview. To make the contrast a bit better, set the data range from -1sigma to the peak determined above.

# In CASA
imview (
  raster={'file': 'Antennae_North.Cont.Clean.image',
  'colorwedge':T,'range':[-0.00049,0.00325]},
  zoom=1, out='Antennae_North.Cont.Clean.image.png')
imview (
  raster={'file': 'Antennae_South.Cont.Clean.image',
  'colorwedge':T,'range':-0.00045,0.00519]},
  zoom=1, out='Antennae_South.Cont.Clean.image.png')

Continuum subtraction

In these data, the continuum emission is too weak to contaminate the line emission (i.e. the peak continuum emission is less than the rms noise in the spectral line channels). Nevertheless, for illustrative purposes we demonstrate how to subtract the continuum emission in the uv-domain using the task uvcontsub2.

# In CASA
uvcontsub2(vis = 'Antennae_North.cal.ms', fitspw='0:1~50;120~164', fitorder = 1)

uvcontsub2(vis = 'Antennae_South.cal.ms', fitspw='0:1~30;120~164', fitorder = 1)

where: fitspw gives the line-free channels for each mosaic and fitorder=1. Higher order fits are not recommended. If you do not have line-free channels on both sides of the line fitorder=0 is recommended. The output ms will have .contsub appended to the name.

CO(3-2) Imaging

Fig. 7a. Northern CO(3-2) uv-spectrum in LSRK velocity space.

Fig. 7b. Southern CO(3-2) uv-spectrum in LSRK velocity space.

Now we are ready to make cubes of the line emission. The imaging parameters are similar to the continuum except for those dealing with the spectral setup: mode, start, width, nchan, restfreq, and outframe parameters. When making spectral images you have three choices for the mode parameter: channel, velocity, and frequency. Data are taken using constant frequency channels. For spectral line analysis it's often more useful to have constant velocity channels, and this is also the best way to make images of multiple lines with the exact same channelization for later comparison. For mode='velocity', the desired start and width also need to be given in velocity units for the desired output frame.

It is important to note that ALMA does not do on-line Doppler Tracking and the native frame of the data is TOPO. If you do not specify outframe the output cube will also be in TOPO, which is not very useful for spectral line work. The Doppler Shift is taken out during the regridding to the desired outframe in clean or alternatively it can be done separately by the cvel task which would need to be run before clean.

To see what velocity parameters you want to set in clean, it is useful to make a plot in plotms in the desired output frame. Note these plots take a little longer because of the frame shift. In order to compare with recent SMA data, we chose LSRK, but it should be noted that many papers of this source are in the BARY frame.

# In CASA
plotms(vis='Antennae_North.cal.ms.contsub/',xaxis='velocity',yaxis='amp',
       avgtime='1e8',avgscan=T,transform=T,freqframe='LSRK',
       restfreq='345.79599GHz',plotfile='North_CO3_2_vel.png')

# In CASA
plotms(vis='Antennae_South.cal.ms.contsub',xaxis='velocity',yaxis='amp',
      avgtime='1e8',avgscan=T,transform=T,freqframe='LSRK',
      restfreq='345.79599GHz',plotfile='South_CO3_2_vel.png')

Northern Mosaic

As before, it is very important that you make a clean mask. There are many ways to do this ranging from the complicated to simple. For this example we will make a single clean mask that encompasses the line emission in every channel and apply it to all channels. This is much better than no clean mask, though not quite as good as making an individual mask for each channel.

Notable parameters included in the clean call are:

• mode='velocity',outframe='LSRK',restfreq='345.79599GHz'. We use 'velocity' mode to set velocity information in the Local Standard of Rest frame (kinetic definition), and use the rest frequency of the CO(3-2) line.
• nchan=60,start='1300km/s',width='10km/s': To produce a data cube with 60 channels("nchan"=60), starting at 1300km/s and with velocity widths of 10 km/s. That will include all the CO(3-2) emission in both mosaics.
• imsize=1000,cell='0.13arcsec'. An image size of 130 arcsec, with pixels of 0.13 arcsec (~ 5 times the minor axis of the synthesized beam). We make the imsize larger than the mosaic to increase the dirty beam image size, as the emission is quite extended along the mosaic.
• weighting='briggs',robust=0.5: Weighting to apply to visibilities. We use Briggs' weighting and robustness parameter 0.5 (in between natural and uniform weighting).
• niter=10000: Maximum number of clean iterations.
• threshold='5.0mJy': Stop cleaning if the maximum residual is below this value.

The threshold is ~ 2 the rms of the line-free channel for each dataset.

Fig. 8a. Interactive cleaning of northern mosaic. The clean mask is shown in white. In this example we used the same mask for all channels by selecting "all channels" before drawing mask.

# In CASA
os.system('rm -rf Antennae_North.CO3_2Line*')
clean(vis='Antennae_North.cal.ms.contsub',
     imagename='Antennae_North.CO3_2Line.Clean',
     spw='0',field='',phasecenter='12',
     mode='velocity',outframe='LSRK',restfreq='345.79599GHz',
     nchan=70,start='1200km/s',width='10km/s',
     imagermode='mosaic',
     imsize=500,cell='0.13arcsec',minpb=0.2,
     interactive=T,
     weighting='briggs',robust=0.5,
     niter=10000, threshold='5.0mJy')

The figure shows what the final clean box should look like. Now clean using the green circle arrow. You can watch the progress in the logger. When 100 iterations are done, the viewer will show the residual map for each channel. Cycle through the channels and see whether you are still happy with the clean box in each signal channel. The "erase button" can help you fix mistakes. If necessary adjust. It is often useful to adjust the colorscale with the "plus" symbol icon. To make it go a bit faster, you can increase iteration interactively, to 200 or 300, but don't overdo it.

These data are pretty severely dynamic range limited, in part due to the sparse uv coverage. In other words, the noise in bright channels is set by a maximum signal-to-noise. Also, we are going to self-calibrate the data so it's best to be conservative here - it can be difficult in images like these to discern real features from artifacts. If in doubt, don't include it in the clean mask. Keep cleaning and see if the feature becomes weaker. You cannot lose real emission by not masking it, but you can create a brighter feature by masking an artifact.

Stop cleaning after about 900 iterations (Red X).

Inspect the resulting data cube:

# In CASA
viewer('Antennae_North.Line.Clean.image')

Southern Mosaic

Fig. 8b. Interactive cleaning of southern mosaic. The clean mask is shown in white. In this example we used the same mask for all channels by selecting "all channels" before drawing mask.

Repeat process for Southern mosaic.

# In CASA
os.system('rm -rf Antennae_South.CO3_2Line*')
clean(vis='Antennae_South.cal.ms.contsub',
     imagename='Antennae_South.CO3_2Line.Clean',
     spw='0',field='',phasecenter='15',
     mode='velocity',outframe='LSRK',restfreq='345.79599GHz',
     nchan=70,start='1200km/s',width='10km/s',
     imagermode='mosaic',
     imsize=750,cell='0.13arcsec',minpb=0.2,
     interactive=T,
     weighting='briggs',robust=0.5,
     niter=10000, threshold='5.0mJy')

Clean about 1200 iterations before stopping.

Inspect the resulting data cube:

# In CASA
viewer('Antennae_South.Line.Clean.image')

The (line-free) channel rms for the northern and southern mosaics are 2.7 mJy/beam and 2.4 mJy/beam, respectively, for 2.3 and 3.8 hours times on source approximately. For comparison, the ALMA sensitivity calculator gives an on-source observing time of ~3-4 hours to reach a noise level of 2.5 mJy using 12 antennas for an angular resolution of 1 arcsec. Note that the fields are overlapping by 0.5 the size of the primary beam. Note however that the dynamic range limit in the channels with line emission leads to significantly worse rms levels than that. Self-calibration and multiscale clean will help to improve this situation.

Self Calibration

Next we attempt to self-calibrate the uv-data. The continuum is far too weak so we will use the CO(3-2) line emission. The process of self-calibration tries to adjust the data to better match the model image that you give it. That is why it is important to make the model as good as you can by making clean masks. The parameter calready=T ensured that a uv-model of the resulting image was placed in the model data column. This model can then be used to self-calibrate the data using gaincal.

Mosaics can be tricky to self-calibrate. The reason is because typically only a few of the pointings may have strong emission. The stronger the signal, the stronger the signal-to-noise will be for a given self-calibration solution interval (solint). This means that typically only a few fields are strong enough for self-calibration, though it can still bring about overall improvement to apply these solutions to all fields. The fine tuning of each field in the mosaic over small solutions intervals is often impossible. Indeed fine-tuning only a few fields in the mosaic on small time scales can result in a mosaic with dramatically different noise levels as a function of position. Below, we will simply attempt to self-calibrate on the strongest field in the mosaic, obtaining one average solution per original input dataset.

Another wrinkle is the self-calibration of spectral line data. To increase signal-to-noise it is often helpful to limit solutions to the range of channels containing the strongest line emission.

We will also use gaintype='T' to tell it to average the polarizations before deriving solutions which gains us a sqrt(2) in sensitivity.

Northern Mosaic

Plot of the CO(3-2) emission in Field 12 of the Northern mosaic.

The strongest emission in the Northern mosaic comes from the center pointing, already identified above as field=12. Below we make a uv-plot of the spectral line emission from this field to chose only the strongest channels to include in the self-calibration.

# In CASA
plotms(vis='Antennae_North.cal.ms.contsub',spw='',xaxis='channel',yaxis='amp',field='12',
       avgtime='1e8',avgscan=T,coloraxis='field')

Next remind ourselves of the timing of the various observations.

# In CASA
plotms(vis='Antennae_North.cal.ms.contsub',spw='',xaxis='time',yaxis='amp',field='12',
       avgchannel='167',avgscan=T,coloraxis='scan')

Zooming in on each dataset we see that they are about 1 hour long (you can also check the listobs output), and that each dataset has 2 or 3 observations of field 12. Each time, it's observed for about 25 seconds. We set solint=3600s to get one solution per dataset.

Phase-only self-calibration solutions for the Northern mosaic.

# In CASA
gaincal(vis='Antennae_North.cal.ms.contsub',caltable='north_self_1.pcal',
        solint='3600s',combine='scan',gaintype='T',field='12',
        refant='DV09',spw='0:80~92',minblperant=4,
        calmode='p',minsnr=2)

Plot the calibration solutions.

# In CASA
plotcal(caltable='north_self_1.pcal',xaxis='time',yaxis='phase',
        spw='',field='',antenna='',
        iteration='antenna',subplot=531,plotrange=[0,0,-80,80],
        figfile='north_pcal1_phase.png')

Apply the solutions to all fields and channels.

# In CASA
applycal(vis='Antennae_North.cal.ms.contsub',field='',
        gaintable=['north_self_1.pcal'],calwt=F)

Re-image the data with the selfcal applied.

# In CASA
os.system('rm -rf Antennae_North.CO3_2Line.Clean.pcal1*')
clean(vis='Antennae_North.cal.ms.contsub',
     imagename='Antennae_North.CO3_2Line.Clean.pcal1',
     spw='0',field='',phasecenter='12',
     mode='velocity',outframe='LSRK',restfreq='345.79599GHz',
     nchan=70,start='1200km/s',width='10km/s',
     imagermode='mosaic',
     imsize=750,cell='0.13arcsec',minpb=0.2,
     interactive=T,mask='Antennae_North.CO3_2Line.Clean.mask',
     weighting='briggs',robust=0.5,
     niter=10000, threshold='5.0mJy')

After 600 iterations or so, inspect each channel to see if there is more emission that needs to be included in the mask. Remember to select the "all channels" toggle. Stop after 1200 or so iterations.

Compare the un-selfcal'ed and self-caled data to determine if there has been improvement.

Unfortunately, we cannot yet script imview to open two cubes to the same channel though this will be fixed soon. For the time being, we will set it up by hand in the viewer

# In CASA
viewer('Antennae_North.CO3_2Line.Clean.image')

Then in the viewer, click on the folder icon, and select Antennae_North.CO3_2Line.Clean.pcal1.image to open as a raster. Then click on the "wrench" icon to get the "data display options" gui. For both cubes (select them with tabs at the top of "data display options" gui) set the Data range to something like -0.05 to 0.3 so you can see faint emission. Then in the "tapedeck" set the channel number to 43. Then select the blink toggle in the "tapedeck", now the tapedeck buttons cycle through the two images at the selected channel. To change the channel toggle back to "normal" change the channel number, and then toggle back to "blink".

Note: while in "blink" mode, statistics will be for the final image in the stack. In "normal" mode, all open raster images will have their statistics reported.

What you should notice is that the peak flux density has increased substantially while the rms noise is about the same. This is reasonable for this self-calibration case because we have mostly adjusted relative position offsets between the datasets and not taken out any short-term phase variations which would reduce the rms.

Note that attempts to push the self-cal to shorter solint (for example to each scan of field=12) did not yield additional improvement. Below we show channel 43 for both images which we obtained by opening the "p wrench" icon selecting the number of panels in x = 2, and making sure "blink" is toggled on.

Comparison of channel 43 before selfcal (left) and after selfcal (right).

Southern Mosaic

Plot of the CO(3-2) emission in Field 7 of the Southern mosaic.

Now repeat the self-calibration process for the Southern mosaic. It is a big tougher in this case to pick the best field. The most compact bright emission is toward field id 11 in the Overview. Adjusting for the renumbering of field ids after final calibration split, this becomes field='7'.

From the following plots we can assess the brightest channels to pick and see that the timing in the 6 Southern datasets is similar to the North, with each lasting about 1 hour.

# In CASA
plotms(vis='Antennae_South.cal.ms.contsub',spw='',xaxis='channel',yaxis='amp',field='7',
       avgtime='1e8',avgscan=T,coloraxis='field')

# In CASA
plotms(vis='Antennae_South.cal.ms.contsub',spw='',xaxis='time',yaxis='amp',field='7',
       avgchannel='167',avgscan=T,coloraxis='scan')

Phase-only self-calibration solutions for the Southern mosaic.

# In CASA
gaincal(vis='Antennae_South.cal.ms.contsub',caltable='south_self_1.pcal',
        solint='3600s',combine='scan',gaintype='T',field='7',
        refant='DV09',spw='0:69~80',minblperant=4,
        calmode='p',minsnr=2)

# In CASA
plotcal(caltable='south_self_1.pcal',xaxis='time',yaxis='phase',
        spw='',field='',antenna='',
        iteration='antenna',subplot=531,plotrange=[0,0,-80,80],
        figfile='south_pcal1_phase.png')

# In CASA
applycal(vis='Antennae_South.cal.ms.contsub',field='',
        gaintable=['south_self_1.pcal'],calwt=F)

# In CASA
os.system('rm -rf Antennae_South.CO3_2Line.Clean.pcal1*')
clean(vis='Antennae_South.cal.ms.contsub',
     imagename='Antennae_South.CO3_2Line.Clean.pcal1',
     spw='0',field='',phasecenter='15',
     mode='velocity',outframe='LSRK',restfreq='345.79599GHz',
     nchan=70,start='1200km/s',width='10km/s',
     imagermode='mosaic',
     imsize=750,cell='0.13arcsec',minpb=0.2,
     interactive=T,mask='Antennae_South.CO3_2Line.Clean.mask',
     weighting='briggs',robust=0.5,
     niter=10000, threshold='5.0mJy')

After 600 iterations or so, inspect each channel to see if there is more emission that needs to be included in the mask. Remember to select the "all channels" toggle. Stop after 2000 or so iterations.

[[Image:|500px|center| Comparison of channel 43 before selfcal (left) and after selfcal (right).]]

Multiscale Cleaning

Normal clean uses a delta function to subtract clean components from the residual image. The clean components (model) is then restored using the clean beam. This works extremely well for unresolved sources, but less well for extended emission. Indeed, when extended emission is cleaned using this method it can take quite a long time and the result is a cotton-candy like appearance in the extended emission. Multiscale clean is an attempt to better clean extended emission by removing clean components at a variety of scales (specified by the user). The emission from all scales are restored to the image correctly using the clean restoring beam resolution. This method also tends to reduce the negative bowls around extended sources due to missing short spacing flux (thought it will not do as good a job as adding the missing spacing information).

Below we demonstrate how this experimental functionality can be applied to the Antennae mosaics. To invoke multiscale, you need only set the multiscale parameter, which is expressed in units of the cell parameter. The first scale should always be set to zero, i.e. the "normal" delta function, that corresponds to the clean beam (i.e. the native resolution of the data given the weighting parameters). There is no definitive recommendation for the other scales, but experimentation suggests that the second scale should be about the size of the synthesized clean beam, and the final scale should never be larger than the largest angular size sampled by the data. In practice making the largest scale larger than the largest features in the data can cause large negative bowls to appear which then have to be compensated for at the other scales making the task run much longer than necessary. It is always best to make a normal clean image before attempting multiscale. For the time being it is best to leave the multiscale subparameters at their default values.

For illustrative purposes we use 3 scales below: 0, 10, 30 or angular sizes of 0, 1.3", and 3.9".

NOTE: Because extended emission is removed on the larger scales, if the chosen scales are well matched to data multiscale cleaning should take significantly fewer iterations to reach similar residual level. Because it has more deconvolution to do, in practice the time to execute is similar to normal clean. In the examples below, it takes on the order of half as many iterations, and this is after we clean a bit deeper because there are fewer artifacts.

# In CASA
os.system('rm -rf Antennae_North.CO3_2Line.Clean.pcal1.multi*')
clean(vis='Antennae_North.cal.ms.contsub',
     imagename='Antennae_North.CO3_2Line.Clean.pcal1.multi',
     spw='0',field='',phasecenter='12',
     mode='velocity',outframe='LSRK',restfreq='345.79599GHz',
     nchan=70,start='1200km/s',width='10km/s',
     imagermode='mosaic',
     multiscale=[0,10,30],
     imsize=750,cell='0.13arcsec',minpb=0.2,
     interactive=T,mask='Antennae_North.CO3_2Line.Clean.pcal1.mask',
     weighting='briggs',robust=0.5,
     niter=10000, threshold='5.0mJy')

After 300 iterations, step through channels and adjust clean mask if necessary. Stop after about 600 iterations.

# In CASA
os.system('rm -rf Antennae_South.CO3_2Line.Clean.pcal1.multi*')
clean(vis='Antennae_South.cal.ms.contsub',
     imagename='Antennae_South.CO3_2Line.Clean.pcal1.multi',
     spw='0',field='',phasecenter='15',
     mode='velocity',outframe='LSRK',restfreq='345.79599GHz',
     nchan=70,start='1200km/s',width='10km/s',
     imagermode='mosaic',
     multiscale=[0,10,30],
     imsize=750,cell='0.13arcsec',minpb=0.2,
     interactive=T,mask='Antennae_South.CO3_2Line.Clean.pcal1.mask',
     weighting='briggs',robust=0.5,
     niter=10000, threshold='5.0mJy')

After 300 and 600 iterations, step through channels and adjust clean mask if necessary. Stop after about 1000 iterations.

Image Analysis

Moment Maps

Next, we make the integrated intensity maps and velocity fields of the CO(3-2) emission using the task immoments. Note that we choose to run the immoments separately for the total intensity map and the velocity field because we want to use different flux thresholds.

For the northern mosaic the moment 0 and 1 can be calculated as follows:

Fig. 6. The CO(3-2) total intensity map (moment 0) of the northern mosaic

Fig. 7. The CO(3-2) velocity field (moment 1) of the northern mosaic

# In CASA
os.system('rm -rf Antennae_North.Line.Clean.Mom.image*') 
immoments('Antennae_North.Line.Clean.image', 
   moments=[0], axis="spec", 
　outfile='Antennae_North.Line.Clean.Mom.image.integrated')

os.system('rm -rf Antennae_North.Line.Clean.Mom.Mask.image.weighted_coord*') 
immoments('Antennae_North.Line.Clean.image', 
   moments=[1], axis="spec", 
    mask="Antennae_North.Line.Clean.image>4.e-2",
   outfile='Antennae_North.Line.Clean.Mom.Mask.image.weighted_coord')

And for the southern mosaic:

Fig. 8. The CO(3-2) total intensity map (moment 0) of the southern mosaic

Fig. 9. The CO(3-2) velocity field (moment 1) of the southern mosaic

# In CASA
os.system('rm -rf Antennae_South.Line.Clean.Mom.image*') 

immoments('Antennae_South.Line.Clean.image', 
   moments=[0], axis="spec",
   outfile='Antennae_South.Line.Clean.Mom.image.integrated')

immoments('Antennae_South.Line.Clean.image', 
   moments=[1], axis="spec", 
   mask="Antennae_South.Line.Clean.image>2.5e-2",
   outfile='Antennae_South.Line.Clean.Mom.Mask.image.weighted_coord')

where:

• moments=[x]: To specify that we wish to make the xth moment map. The 0th moment map gives integrated emission and the 1st gives the intensity-weighted velocity field
• axis='spectral': Indicates the moment axis; in this case, 'spectral'
• mask="Antennae_North.Line.Clean.image>X" Mask applied to the image before calculating the moments. Consider pixels in Antennae_North.Line.Clean.image that are larger than X
• outfile='Antennae_South.Line.Clean.Mom.image.XX': The output image name

Finally, we visualize the different moments using imview:

# In CASA
imview (
  raster={'file': 'Antennae_North.Line.Clean.Mom.image.integrated',
  'colorwedge':T,},
  zoom=1, out='Antennae_North.Line.Clean.Mom.image.integrated.png')

imview (
   raster={'file': 'Antennae_North.Line.Clean.Mom.Mask.image.weighted_coord',
   'range': [1500,1750],'colorwedge':T},
   zoom=1, out='Antennae_North.Line.Clean.Mom.Mask.image.velfield.png')

imview (
   raster={'file': 'Antennae_South.Line.Clean.Mom.image.integrated',
   'colorwedge':T},
   zoom=1,out='Antennae_South.Line.Clean.Mom.image.integrated.png')

imview (
   raster={'file': 'Antennae_South.Line.Clean.Mom.Mask.image.weighted_coord',
   'range': [1300,1900],'colorwedge':T},
   zoom=1, out='Antennae_South.Line.Clean.Mom.Mask.image.velfield.png')

Comparison with previous SMA CO(3-2) data

We compare with SMA CO(3-2) data (Ueda, Iono, Petitpas et al., in preparation, to be submitted to ApJ). Figure 13 shows a comparison plot betwee the moment 0 maps of ALMA and SMA data using the viewer. The fluxes, peak locations and large scale structure are consistent. Both southern and northern components have been combined.

Fig. 13. The CO(3-2) total intensity map (moment 0) comparison with SMA data. Colour image is ALMA data, combining southern and northern mosaics. contours show SMA data (Ueda, Iono, Petitpas et al., in preparation, to be submitted to ApJ).

Exporting to Fits

You can convert from CASA format to FITS if you want to analyze the data using another software package. If you have difficulty with the standard FITS output from CASA, try setting velocity=T and/or dropstokes=T.

# In CASA
exportfits(imagename='Antennae_North.Line.Clean.image',
     fitsimage='Antennae_North.Line.Clean.image.fits')
exportfits(imagename='Antennae_North.Line.Clean.Mom.image.integrated',
     fitsimage='Antennae_North.Line.Clean.Mom.image.integrated.fits')
exportfits(imagename='Antennae_North.Line.Clean.Mom.Mask.image.weighted_coord',
     fitsimage='Antennae_North.Line.Clean.Mom.Mask.image.weighted_coord.fits')

# In CASA
exportfits(imagename='Antennae_South.Line.Clean.image',
     fitsimage='Antennae_South.Line.Clean.image.fits')
exportfits(imagename='Antennae_South.Line.Clean.Mom.image.integrated',
     fitsimage='Antennae_South.Line.Clean.Mom.image.integrated.fits')
exportfits(imagename='Antennae_South.Line.Clean.Mom.Mask.image.weighted_coord',
     fitsimage='Antennae_South.Line.Clean.Mom.Mask.image.weighted_coord.fits')